QNAP TS-1270U-RP Скачать руководство пользователя страница 21

Страница: 21 / 83

Chapter 2.

Power Button and Reset Button Behavior



Power button: Press to turn on or turn off.

System

Power button
(Turn on)

Power button
(Hardware turn
off)

Power button
(Force turn off)

All models

Press once

1.5 sec

5 sec



Reset button: Press to reset the system settings.

System

Basic system reset
(1 beep)

Advanced system reset
(2 beeps)

All models

3 sec

10 sec

Basic system reset (3 sec)

Press the reset button for 3 seconds, a beep sound will be heard. The following settings
are reset to default:



System administration password: admin



TCP/IP configuration: Obtain IP address settings automatically via DHCP



TCP/IP configuration: Disable Jumbo Frame



TCP/IP configuration: If port trunking is enabled (dual LAN models only), the port
trunking mode will be reset to “Active Backup (Failover)”.



System Port: 8080 (system service port)



Security Level: Low (Allow all connections)



LCD panel password: (blank)*



VLAN will be disabled

*This feature is only provided by the NAS models with LCD panels. Please visit
http://www.qnap.com for details.

Содержание TS-1270U-RP



















































































Результаты поиска

Содержание TS-1270U-RP

Отзывы:

Похожие инструкции для TS-1270U-RP

Бренды по названию

Популярные бренды

QNAP TS-1270U-RP, Руководство пользователя по оборудованию

Результаты поиска

Содержание TS-1270U-RP

Отзывы:

Похожие инструкции для TS-1270U-RP

Бренды по названию

Популярные бренды