Qlogic SilverStorm 9000 Скачать руководство пользователя страница 50

Страница: 50 / 210

2 – Switch Command Line Interface
Groups and Commands

2-44

D000025-002 Rev. A

showLastScpRetCode

Display the return code from the last SCP Firmware Push.

Syntax:

Options:

Sample Output:

NOTES:

This allows for automated systems to determine if a SCP firmware push

was successful or not.

fwVersion

Displays the firmware versions for a unit.

Syntax:

Options:

Sample Output:

showLastScpRetCode slot | -all

slot

The slot number in the chassis.

-all

All slots in the chassis.

-> showLastScpRetCode 101
SCP: Slot 101 Last Exit Code: 0: Success

fwVersion [slot]

slot

Slot number.

-> fwVersion 3
Slot 3 Information -----------------
Firmware Version: 4.0.0.0.32
Firmware build: 4_0_0_0_32
Firmware BSP: t3=9000 chassis
MBC Version: None
Bootrom Version: 4.0.0.0.28

Содержание SilverStorm 9000



















































































































































































































Результаты поиска

Содержание SilverStorm 9000

Отзывы:

Похожие инструкции для SilverStorm 9000

Бренды по названию

Популярные бренды

Qlogic SilverStorm 9000, Справочное руководство

Результаты поиска

Содержание SilverStorm 9000

Отзывы:

Похожие инструкции для SilverStorm 9000

Бренды по названию

Популярные бренды