Qlink LG250 Скачать руководство пользователя страница 13

Страница: 13 / 44

HEADLIGHT ILLUMINATION SWITCH

①

Press button, and the high beam is on.
Press button, and the low beam is on.

TURNING LIGHT SWITCH

②

Press the switch to , and left turning light is on.
Press the switch to , and right turning light is on.
Press down the button, and turning light will be off.

HORN SWITCH BUTTON

③

Press the button, and the horn will sound.

IGNITION BUTTON

④

Press this button, and engine can be started (Refer to P20 for details).

HEADLIGHT SWITCH

⑤

The headlight switch consists of three positions: , and ;

: when the switch is at this position, headlight, the front pilot light, the rear pilot light and instrument light are on.

: when the switch is at this position, the front pilot light, the rear pilot light and instrument light are on.

: when the switch is at this position, headlight, the front pilot light, the rear pilot light and instrument light are off.

KILL SWITCH

⑥

Press button, and engine can be stopped..
Press button, and engine can be started.

OVERTAKE LIGHT SWITCH

⑦

Press this button, and headlight high beam will be on, which indicates the signal of passing to the vehicle in front.

USER'S MANUAL

Содержание LG250













































Результаты поиска

Содержание LG250

Отзывы:

Похожие инструкции для LG250

Бренды по названию

Популярные бренды

Qlink LG250, Руководство пользователя

Результаты поиска

Содержание LG250

Отзывы:

Похожие инструкции для LG250

Бренды по названию

Популярные бренды