QERIDOO Sportrex1 Скачать руководство пользователя страница 10

18

  – 02|2017 – Subject to change. 

Sportrex

Sportrex

 

Subject to change. – 02|2017 – 

19

Assembly

Assembly

tow bar mount and folding down the securing bracket. 

Tip!

You do not have to remove the tow bar completely. Simply place the tow bar into the 

tow bar mount from behind to stow it under the cabin floor, see 

“Insert tow bar” on 

page 22

.

Mounting the coupler onto a bicycle 

Danger!

Make sure that your bicycle is suitable for towing a bicycle trailer, see 

“Performance 

limits” on page 4

. Since it may in some cases be necessary to change the rear 

wheel axle, it is best to consult your specialist dealer or the bicycle manufacturer in 

order to do this.

Caution!

Secure the bicycle to prevent it from toppling over, and make sure that the rear wheel 

cannot drop out of the axle mount after the screw connection has been undone. Use 

for example an assembly stand, or turn the bicycle upside down so that you can place 

it on its saddle and handlebars. 

In the as-delivered state, the supplied coupler is connected to the tow bar:

 

f

Undo the cotter pin fastening and remove the coupler.

 

f

Next, insert the cotter pin fastening back into the 

coupler pocket of the tow bar.

 

f

Prepare the bicycle for mounting the coupler by 

undoing the screw connection of the rear wheel axle: 

 

Quick-release axle: Open the bracket of the quick-release axle and unscrew the cap nut on 

the other side of the rear wheel axle. 

 

Full axle: Unscrew the nut on the left side of the rear wheel axle.

 

f

Mount the coupler on the rear wheel axle:

 

Place the large hole of the coupler onto the left 

side of the rear wheel axle so that the coupler is 

facing outwards. 

 

Screw on the dedicated nut and tighten it slightly.

 

Align the rear wheel so that it can turn freely.

 

Align the coupler so that it faces horizontally to the 

rear.

 

f

Tighten the connection firmly in order to secure the rear wheel:

 

Quick-release axle: Tighten the cap nut until you can close the clamp with a certain amount 

of pressure. 

 

Full axle: Tighten the nut with a spanner. Always pay attention to the bicycle manufacturer’s 

notes about the tightening torque. 

Caution!

Due to the construction of the coupler, slight wear and tear in the form of scratches 

can occur at the connection between bicycle frame and coupler. This is not a reason 

for a complaint. 

Danger!

Do not use a washer or similar at the connection between the bicycle frame and 

coupler because this could negatively affect the stability of the connection.

Tip!

The supplied universal coupler is suitable for mounting on most rear-wheel versions. 

If it does not fit your bicycle, you can find suitable special couplers and conversion sets 

on the Weber Technik GmbH website: 

www.weber-products.de

Содержание Sportrex1




















Отзывы: