IS535 ECN 3673
Page 5 of 9
to the thinnest part of the ‘power level’ and the
highest level to the widest part.
Indicator Display Table
Power level setting
There are continuously variable power level settings
available via the rotary control knob.
Residual heat display
When a pan is removed from the hobtop and the
temperature of the ceramic glass exceeds 60
C, the ‘H’
symbol is displayed indicating a hot sur
face. Whilst the ‘H’
display is showing, leave the induction hob connected to
the power supply. This will allow the internal cooling fans to
operate. When the ‘H’ symbol is extinguished, the mains
power supply may be switched off.
Error Codes
There are numerous error codes that identify issues within
the induction system and are primarily of use when
reporting a fault to the Service Department at Lincat. Some
errors can be cleared by turning the control to the ‘Off’
position, or completely turning off and disconnecting the
appliance before switching on again.
Pan detection function
Each zone has pan detection; this prevents the coil from
turning on without a pan present. The coil also turns off as
soon as the pan is removed.
Performance issues
A reduction in performance during cooking may be
attributed to any of the following:- a blocked air filter, a
confined location with insufficient cooling air flow or a failed
fan. These circumstances will cause the generator to
overheat. Eventually the control electronics will then shut
down the generator. (See cleaning air filter
– Care and
Maintenance).
Switching off the glass ceramic induction cooking hob
Turn the knob to the ‘Off’ position and isolate the
appliance at the mains.
CARE AND MAINTENANCE
Do not use a water jet or steam cleaner, and do
not immerse this appliance.
Always disconnect the appliance from the power
supply before cleaning or maintenance.
Steel parts can be cleaned using a cloth with
water and mild detergent
– aggressive or abrasive
cleaning substances such as steel wool or chlorine
based products must be avoided.
Do not use sharp objects during cleaning.
If the appliance is not to be used for a lengthy
period, disconnect from the mains supply and
clean well.
Cleaning the glass ceramic induction cooking hob
Do not use abrasive materials or detergents.
Do not use aggressive products such as oven
sprays.
Liquefied plastic materials or sugar must be
removed
immediately
with a suitable scraper
before the hob cools down.
When at an acceptable temperature, use a
scraper to remove debris from the glass ceramic
cooking hob.
Next clean the glass with a suitable product and
paper towels. Wipe with a damp cloth and dry.
Cleaning/Replacement of air filter
Removing and cleaning the air filter will ensure an
adequate supply of cool air and will restore
performance.
Disconnect the appliance from the power supply
after allowing to cool.
Access the air filter by tipping the appliance up at
the front
– the air filter is installed beneath a pull
down latched flap in the base.
Remove the filter and clean
– the filter may be put
in a dishwasher.
Replace clean filter and re-engage the latch.
Reconnect to the power supply.
Warning
Do not operate the appliance without a filter otherwise
dirt and grease will be drawn into the electronics,
impairing performance and safety.
SPARE PARTS LIST
Glass ceramic hob CG107(Q2) CG108(Q4)
Inductors IM08
Generator IM09(Q2) IM07(Q4)
Control knob 761-005-00
6 pole terminal block X59000
Rotary control (with LED) IM12
Air filter FI36
EU DIRECTIVE 2002/96/EC (WEEE)
This information note is intended exclusively for
appliances marked with the symbol
shown on the data plate applied onto
the actual product (registration label).
This symbol indicates that the appliance is
classified according to current legislation as an
electrical or electronic device. In compliance with
EU Directive 2002/96/EC (WEEE), this appliance
at the end of its service life must not be treated as
normal household waste but handed in free of
charge to available differentiated collection system
for electrical or electronic devices. The user is
responsible for delivering the used product to any
provided collection systems and is otherwise
subject to penalties in accordance with current
legislation on waste products. By using a suitable
collection system for the reuse, treatment and
waste management for environmental protection,
you are promoting recycling of the materials in this
appliance and contributing to protecting the
environment and health.
For more information concerning the available
differentiated collection systems, please consult
the local authorities or the supplier from which this
ENG
Power level setting 1-100
Residual heat display
Error codes - generator
Pan detection (no pan present)