Q-FREE MD 5850 MultiReader Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 21

Q-FREE MD 5850 MultiReader Скачать руководство пользователя страница 15

MD 5850

Installation Manual

•

Turn the HyperTerm off and on (due to a bug in the HyperTerm SW) and thereafter the terminal
must be set to the same baud rate as in frame above. (Choose properties and configure to change
baud rate).

•

Type the command

‘lo 0 10000’

and press enter (

lo

= letters)

The CPU-card gives no

response and no prompt to this command, it is waiting for the software.

•

Select the menu ‘Transfer’ and ‘Send Text File’ on the HyperTerm.

•

As filename select the application software (hex format) from the SW archive, PC hard disc or
from the supplied diskette.

•

The HyperTerm program gives no indication that it is sending the file and the READER shall not
print out anything either. If you try to select a menu then the response is very slow indicating that
the program is working.

•

The loading of the file will take between 10-15 minutes.

•

After the loading is finished then you can press

‘

enter

’

to get the

‘162-BUG->’

prompt.

•

Now type

‘pflash 10000 10ffff ffa00000’

•

The response from the CPU-card should be something like this:

162-Bug>pflash 10000 10ffff ffa00000

Source Starting/Ending Addresses =00010000/0010FFFF
Destination Starting/Ending Addresses =FFA00000/FFAFFFF7
Number of Effective Bytes =000FFFFF (&1048575)

Program FLASH Memory (Y/N)?

•

Type

‘Y’

and enter to start the flashing.

Zeroing Block Number =00 ($FFA00000)
Zeroing Block Number =01 ($FFA40000)
Zeroing Block Number =02 ($FFA80000)
Zeroing Block Number =03 ($FFAC0000)
Erasing Block Number =00 ($FFA00000)
Erasing Block Number =01 ($FFA40000)
Erasing Block Number =02 ($FFA80000)
Erasing Block Number =03 ($FFAC0000)
Programming Block Number =00 ($FFA00000)
Programming Block Number =01 ($FFA40000)
Programming Block Number =02 ($FFA80000)
Programming Block Number =03 ($FFAC0000)
FLASH Memory Programming Complete

162-Bug>

•

The number of blocks depends on the type of application software.

5.1.2 Closing

up.

•

Now you have to turn off power and replace the jumper removed earlier. On MVME162P set
switch S4 on dipswitch 5 in position “ON”. Leave the other jumpers in positions described in 5.1.

•

Turn the HyperTerm off and on (due to a bug in the HyperTerm SW) and thereafter the terminal
must be set to baud rate 9600.

•

Now turn on the power and check that the software boots before you close the box. There might
be some Errors at this point, but you should have the prompt.

•

Fasten the CPU-screws, close the box and fasten the bolts.

Q-Free

®

ASA

645-054-1999 rev.4

14 of 20

1

pflash 10008 10ffff ffa00000 for sw older than 1999.

«
...
13
14
15
16
17
...
»

Содержание MD 5850 MultiReader






















Отзывы:

Нет отзывов