Pyxis ST-601 Скачать руководство пользователя страница 4

 

 

Pyxis ST-601 

Operation Manual 

 

1

 

Introduction 

The Pyxis ST-601 inline probe are uniquely designed to measure the real-time mass/mass concentration 
of chlorine dioxide (ClO2) in a range of 0.01-0.35%. The ST-601 probes measure the optical absorbance 
of the ClO2 solution using a UV light source. The probes have a built-in reference light source and a 
reference light detector in addition to the main light source and main light detector. The ST-601 probes 
can be connected to any device that accepts an isolated or non-isolated 4-20mA input or RS-485 
Modbus.  As with all Pyxis inline sensors, the ST-601 probes can be wirelessly accessed via Bluetooth 
when used in conjunction with the MA-WB Bluetooth Adapter or PowerPACK Series Auxiliary Box and 
the 

uPyxis

 App for Mobile phone and PC.  Instructions on this wireless calibration capability are included 

in this manual. 

PRIMARY INSTALLATION FORMAT 

The primary method is to install the probe in-line with of the suction side of the chemical feed pump in 
piping format.   This method should ideally in a vertical line run to avoid chlorine gas bubble 
interference.  This can be done with the standard ST-

001 Inline Tee Assembly (3/4” FNPT) provided with 

each sensor.  

Pyxis also offers 2” and 3” inline tee assemblies as an accessory option if required.

 

TEFLON TUBE INSTALLATION FORMAT  

The second method is to install the probe in-line using the unique 

¼” OD

 (7mm OD) clear Teflon tubing 

adapter 6 inches in length

.  This tubing can be passed “THROUGH” the optical channel to allow for use of 

the sensor with smaller chemical feed line installations on the suction side of the chemical feed pump. 

*NOTE* for enhanced ambient light interference prevention, Pyxis commends users apply black 
electrical tape or shrink wrap to allow sample darkening prior to and after the optical channel as seen 
in the sensor photo in the Section 2 of this manual.

  

1.1

 

Features of the Pyxis ST-601 

The ST-601 probes include the following features: 

 

The probe can be conveniently connected to the suction or discharge side of the pump in both 
inline Tee (ST-001) or 

¼” 

Teflon tubing format with using a union.   Both included with probe. 

 

 

The probe can be calibrated with Mobile App or PC software via a MA-WB Bluetooth adapter or 
PowerPACK Series Aux. Box. 

 

 

Diagnostic information (probe tubing fouling and failure modes) can be communicated to digital 
displays via Modbus RTU. 

 

 

ST-601 can be wireless calibrated using known chlorine dioxide concentration standards via 

uPyxis

 App for Mobile phone or PC. 

 

Содержание ST-601



















Отзывы: