Pyxis 53607 Скачать руководство пользователя страница 14

SP-765SS Series Sensor Manual 

[email protected] 

|  +1 (866) 203-8397 

12 

 

4.1.1.2

 

       Two-Point Calibration Procedure 

Zero-point Calibration:   Launch the uPyxis app and connect to the ST-765SS sensor. Remove the ST-765SS 

sensor from the FR-50  flow  reservoir  and place the sensor into a beaker containing  Pyxis  Zero Chlorine 

Calibration Standard Solution (P/N 21022), then  tap 

ZERO CALIBRATION

  in the uPyxis app.  Please allow 

sufficient time (a few minutes) for the sensor to stabilize before performing the calibration.

 

*NOTE*

 Users 

may also use up to 100 us/cm conductivity standard as a ZERO CALIBRATION solution. 

Slope-point Calibration: Insert the ST-765SS Series sensor back into the FR-50 flow reservoir and reestablish 

sample flow.  The ST-765SS Series must be slope calibrated in the FR-50 flow reservoir provided with the 

sensor and must have 

CONSISTENT

 flow within the specified range of 200 to 400mL per minute. Determine 

the Free Chlorine or Chlorine Dioxide concentration in ppm (mg/L) of the sample water taken from the FR-

50 output sample by using the DPD method on the handheld Pyxis SP-200 Oxi-Pocket  (P/N 50802) or 

alternative compliant colorimeter.  Launch the uPyxis app and connect to the ST-765SS Series sensor. Tap

 

SLOPE CALIBRATION

. Enter the free chlorine or chlorine dioxide concentration determined by the DPD 

method in the dialog window as shown in Figure 6 based on the model sensor you are calibrating. Please 

make sure that the sensor reading has been stable for at least 10 minutes before calibration. For best 

results, the concentration of the Free Chlorine and Chlorine Dioxide sample flow standard should be in the 

range of 0.1 to 5.0 ppm. 

Figure 8   Enter Free Chlorine or Chlorine Dioxide concentration to begin slope calibration 

Содержание 53607




























Отзывы: