Python 872 Скачать руководство пользователя

Страница: 72 / 91

locked) during remote start and after shut down

On: the Door lock and Factory Alarm Re-arm outputs will arm/lock the vehicle during remote start

and after shutdown

Bitwriter - Only Options

If programming with the Bitwriter®, the learn routine can be locked or unlocked. If the learn routine

has previously been locked, it must be unlocked with Bitwriter® - this cannot be done manually with

the Control button.

The Bitwriter®

gives you access to a wider range of system options. These features and the adjustments

that may be programmed are described in the table below.

Item

Feature

Default

Opt. 2

Opt. 3

Opt.4

Opt. 5+

Zone 4 Sensor Type*

None

Shock/Omni Field Distur-

bance

Tilt Sensor

Glass Break (5)/Ultra-

sonic (6)

Siren Duration

30 sec.

Options: 1 to 180 sec.

Aux/Trunk Icon Type*

Trunk

Window

Sunroof

Audio

Lights/Left dr/Right dr/

Rear Hatch

Aux 1 Timed Output

30 sec.

Options: 1 to 90 sec.

Aux 1 Icon Type*

Pulsed

Trunk

Window

Sunroof

Audio/Lights/Left dr/

Right dr/Rear Hatch/

Timed/Latched

Aux 2 Timed Output

30 sec.

Options: 1 to 90 sec.

Aux 2 Icon Type*

Pulsed

Trunk

Window

Sunroof

Audio/Lights/Left dr/

Right dr/Rear Hatch/

Timed/Latched

Aux 3 Timed Output

30 sec.

Options: 1 to 90 sec.

Aux 3 Icon Type*

Pulsed

Trunk

Window

Sunroof

Audio/Lights/Left dr/

Right dr/Rear Hatch/

Timed/Latched

Aux 4 Timed Output

30 sec.

Options: 1 to 90 sec.

Diesel Start Delay Timer

15 sec.

Options: 1 to 90 sec.

Timer Mode Runtime

12 min.

Options: 1 to 16 min.

Timer Mode Starts

6 starts

Options: 1/2/3/4 to

24 (Starts) in increments of 2

Timer mode intervals

3 hr.

Options: 1/2/3/4 to 24 in 2 hour increments

Smart start low temp

0° (F)

Options: OFF, -20° to 70° in 10° increments

Smart start high temp

100° (F)

Options: OFF, 40° to 130° in 10° increments

Smart start low battery (volts)

10.5V

Options: OFF, 9V to 12.5V in 0.5V increments

Sensor 1 Level

Options: 0 to 15 in increments of 1

Starter Release Fine Tune

(normal)

Options: 0 to 20 in increments of 1

Feature Programming

Unlocked

Locked

Transmitter Programming

Unlocked

Locked

Remote Start Runtime

12 min.

Options: 1 to 60 min.

Virtual Tach Fine tune

Not Initial-

ized

Options: Not initialized, 0 to 1000 in 50 millisecond increments

* Not available on 1-way remote

Содержание 872




























































































Результаты поиска

Содержание 872

Отзывы:

Похожие инструкции для 872

Бренды по названию

Популярные бренды

Python 872, Руководство пользователя

Результаты поиска

Содержание 872

Отзывы:

Похожие инструкции для 872

Бренды по названию

Популярные бренды