PVI VeCOAX ULTRA-HDMI-QAM-IP Скачать руководство пользователя страница 23

Страница: 23 / 24

– All Rights Are Reserved

Page 21 / 24

Chapter 4 Troubleshooting

Please visit

www.pvisupport.com

or call 407 720 6101 ext #2

The Free Tech Support Service is active Mon-Fri

– 10Am – 4PM Est on regular

business days

Prevention Measures

➢

Installing the device at the place in which environment temperature between

0 to 45 °C

➢

Making sure good ventilation for the heat-sink on the rear panel and other

heat-sink bores if necessary

➢

Checking the input AC within the power supply working range and the

connection is correct before switching on device

➢

Checking the RF output level varies within tolerant range if it is necessary

➢

Checking all signal cables have been properly connected

➢

Frequently switching on/off device is prohibited; the interval between every

switching on/off must greater than 10 seconds.

Conditions need to unplug power cord

➢

Power cord or socket damaged.

➢

Any liquid flowed into device.

➢

Any stuff causes circuit short

➢

Device in damp environment

➢

Device was suffered from physical damage

➢

Longtime idle.

➢

After switching on and restoring to factory setting, device still cannot work

properly.

➢

Maintenance needed

Содержание VeCOAX ULTRA-HDMI-QAM-IP

























Результаты поиска

Содержание VeCOAX ULTRA-HDMI-QAM-IP

Отзывы:

Похожие инструкции для VeCOAX ULTRA-HDMI-QAM-IP

Бренды по названию

Популярные бренды

PVI VeCOAX ULTRA-HDMI-QAM-IP, Руководство пользователя

Результаты поиска

Содержание VeCOAX ULTRA-HDMI-QAM-IP

Отзывы:

Похожие инструкции для VeCOAX ULTRA-HDMI-QAM-IP

Бренды по названию

Популярные бренды