background image

128-6528

5 of 28

SHOCK SENSOR:
Select a centrally located,  solid mounting surface for the shock sensor that will allow consistent opera-
tion from all areas of the vehicle.  The selected location must be within 18" of the control module to allow
routing and connecting of the 4 pin harness.  Secure the shock sensor to the chosen location using two
#8 self tapping sheet metal screws.  The sensor can also be secured to an existing dash brace using
cable tie straps.  Whichever mounting method is used be sure to allow access to the sensitivity adjust-
ment potentiometer for use later in the installation.

STARTER INHIBIT RELAY:
Select a mounting location within 12" of the ignition switch's low current start solenoid wire.  Secure the
relay to an existing harness in the chosen location using a cable tie around the relay's wiring harness.
CAUTION! Do not wire tie the metal bracket to an existing wiring harness as vibration may cause chaffing
and shorting damaging the factory wiring.  If an existing harness is not available then secure the relay's
metal mounting tab to an under dash metal brace with a #8 self tapping sheet metal screw.  Wire the relay
as per the diagram found later in this manual.
This unit is to be used in vehicles with AUTOMATIC TRANSMISSIONS only!  Although this combination
Alarm/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be
installed into a vehicle with a manually operated transmission.  Doing so may result in serious per-
sonal injury and property damage.
IMPORTANT!
DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS
INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE.
AFTER SELECTING YOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE
BATTERY CABLE FROM THE VEHICLE BATTERY PRIOR TO MAKING ANY CONNECTIONS.

WIRING THE 6 PIN MAIN POWER HARNESS:
RED w/ WHITE
 Trace Wire:  + 12 volts Battery 1 Source
Connect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp
fuse and holder provided.  This wire provides power for the control circuit as well as the ignition 1 and
ignition 2 relays.

RED Wire:  + 12 Volts Battery 2 Source
Connect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp
fuse and holder provided,  but NOT the same vehicle wire as used by the battery 1 source.  Most vehicles
have more than one battery source supplying power to the ignition switch.  Separate feed wires must be
used for the Red and Red/White wires.  If your vehicle does not have two battery feed wires at the ignition
switch then it is possible to connect both wires to the vehicle's battery.  This wire provides power for the
start relay and the accessory relay.
IMPORTANT!
It is the responsibility of the installing technician to determine the load factor of the vehicles electrical
circuits when the vehicle is running, and to adequately fuse the two power wires based on that load.  If the
vehicle, running under load with the air conditioner, heater blower motor, and accessories exceed 24
Amps continuous, we recommend that two fuses be used in combination on each power wire as shown
below.  For additional information see Tech Update issued 9/30/96.

5

Содержание PRO-9800





























Отзывы: