background image

128-9110

1 of 12

Page 1

Model  PA-320C

Installation Manual

Programmable Features

Select By Operating Transmitter              Press Lock Button          Press Unlock Button
Siren Indications

1 Chirp

  2 Chirps

Factory Default

1)  Arming Method

Passive Arm

Active Arm

Passive Arm

2)  Ignition Control Lock/Unlock

Off

On

Off

3)  Passive Or Active Door Locks

Active

Passive

Active

4)  Single Or Double Pulse U/L

Single Pulse

Double Pulse

Single

5)  Door Lock/Unlock Pulse Duration

1  Second

3  Seconds

1  Second

6)  Siren Chirps On/Off

On

Off

On

7)  Passive Rearm From Active State

On

Off

On

8)  Anti Hi-Jack Feature

Non Operational

Operational

Non Operational

9) Park Lights

Normal

15  Sec w/Lock

Normal

To Program The Selectable Features:

1. Enter the vehicle, and turn the ignition key to the on position.
2. Press and release the valet/override/program push button switch 3 times.

Siren Chirps Once & Led Flash Once

3. Within 3 seconds, turn the ignition off than on, you will hear short chirp followed by long chirp.
4. Press and release the valet pushbutton switch one time to access feature #1.  Use transmitter buttons to

change, or press the valet pushbutton switch to advance to the next feature.  Turn the ignition switch off, or allow 60 seconds of
inactivity to exit the feature program mode.

NOTE

: While in the program mode, if the ignition switch is turned off, or if 60 seconds of inactivity expire the program mode will

terminate, indicated by one short and one long chirp of the siren.

INSTALLATION OF THE MAIN COMPONENTS
Control Module : (P/N 1365273)

Select a mounting location inside the passenger compartment (up behind the dash), and secure using the two screws
provided. The control module can also be secured in place using cable ties.

Do not

 mount the control module in the engine compartment, as it is not waterproof. You should also avoid mounting

the unit directly onto factory installed electronic components. These components may cause RF interference, which
can result in poor transmitter range or intermittent operation.

Siren:

 

(P/N 1365270)

Select a mounting location in the engine compartment that is well protected from access below the vehicle. Avoid areas
near high heat components or moving parts within the engine compartment. To prevent water retention, the flared end
of the siren must be pointed downward when mounted.
Mount the siren to the selected location using the screws and bracket provided.

Shock Sensor: ((P/N 4700023)

Select a solid mounting surface for the shock sensor on the firewall inside the passenger compartment, and mount the
sensor using the two screws provided. The shock sensor can also be secured to any fixed brace behind the dash using
tie straps.
Whichever mounting method is selected, make certain that the sensitivity adjustment is accessible for use later in the
installation.

Hood or Trunk Pin Switch: (P/N 1363699)

A pin switch, not included, is intended for use in protecting the hood or trunk (or hatchback) of the vehicle. The switch
must always be mounted to a grounded, metal surface of the vehicle. It is important to select a location where water

Содержание PA-320C













Отзывы: