PURSUIT C238 Скачать руководство пользователя

Страница: 19 / 118

Helm Systems

2-5

Section 2

C238

Trim Tab Maintenance

Marine growth can affect the operation of the

trim tab planes and actuators. To help

reduce marine growth, return the trim tabs to

the full “UP” position after operating the

boat. Inspect and clean the actuators and

planes regularly.

The trim tabs also include a zinc anode to

help prevent galvanic corrosion. Galvanic

corrosion occurs when different metals are

submerged in an electrolyte. Sea water is an

electrolyte and submerged metal compo-

nents must be protected. Anodes were fac-

tory installed and need to be replaced when

they are 75% of their original size.

Refer to Routine Maintenance for informa-

tion regarding zinc anodes and the trim tab

owner’s manual for additional maintenance

information, fluid specifications and operat-

ing instructions.

WARNING

LOSS OF CONTROL AND UNSAFE

BOAT HAZARD

Improper maintenance of steering

system is hazardous and can cause

death or serious injury from sudden

loss of control. Make sure all steering

hardware, and fluid levels are regu-

larly inspected and maintained.

DO NOT attempt to service any part of

the steering system unless you are

familiar or qualified to do so. Follow

all instructions regarding mainte-

nance procedures in the steering sys-

tem owner’s manual.

Содержание C238























































































































Результаты поиска

Содержание C238

Отзывы:

Похожие инструкции для C238

Бренды по названию

Популярные бренды

PURSUIT C238, Руководство пользователя

Результаты поиска

Содержание C238

Отзывы:

Похожие инструкции для C238

Бренды по названию

Популярные бренды