Puro PURO-35T Скачать руководство пользователя страница 11

11

NOTE: If you want to pull the tubing out for 

some reason, push the ring around the 

tubing in and pull the tubing out.

D.  R.O. Manifold Assembly Installation 

  Locate the site per Sec. III, C.3. Various 

installation sites will require different types 

of mounting fasteners; be sure the fastener 

selected will provide a firm, solid mounting. 

A support panel may be necessary on thin 

cabinet walls or to span between wall studs on 

particleboard or drywall. 

  Do not drill through exterior cabinet walls or 

leave sharp wood screw points exposed in 

readily accessible cabinet interiors. 

  The close proximity of a dishwasher or a trash 

compactor may require special fabrication of a 

mounting plate.
1.  The mounting bracket will accept either #10 

or #12 (5mm) mounting screws spaced on 

6" (15 cm) centers. Allow at least 4" (10 cm) 

of clearance beneath the filter housings to 

accommodate filter changes. Mark the two 

locations (the bracket can be used as a 

template). Install the screws and tighten them 

until the heads are about 

5

/

8

" from the wall.

RED

BLACK

YELLOW

IN

DRAIN

OUT

DRAIN 

RESTRICT

OR

2.  Locate the ¼" Red Feed Water Tubing. 

Remove the red plug from the fitting labeled 

“In” on the manifold and insert the tubing. 

Reference the special supplement sheet in 

the carton for proper connection of all tubing 

and removal of plugs. Run the tubing along 

its course to the Feed Water Saddle Valve, 

trim to length. (Refer to Fig. 1.) 

  Refer to Fig. 3. To the end of the red polytube 

install the Compression Nut, the  Plastic 

Ferrule, and the Brass Insert. Connect to the 

Feed Water Saddle Valve.

3.  Locate the ¼" Black Drain Tubing connected 

to the Dispensing Faucet. The end of the 

Black Drain Tubing that should be inserted 

into the “Drain” port on the manifold will have 

a drain restrictor in it. Remove the black 

plug from the fitting labeled “Drain” on the 

manifold and insert the tubing. Allow the 

tubing to relax, then press firmly again to 

insure proper seating.

4.  Locate the ¼" yellow tubing with the tee 

attached to one end. Remove the yellow plug 

from the fitting labeled "Out" on the manifold 

and insert the tubing.

5.  Locate the 

3

/

8

" Blue Product Water Tubing 

attached to the Dispensing Faucet. Firmly 

press one end into the tee. (Refer to Fig. 

1, page 5.) The fittings will grab the tubing 

and seal it in place. Make sure the tubing is 

pressed all the way in to create a pressure 

tight connection. 

 

NOTE:

 If you want to pull the tubing out 

for some reason, push the ring around the 

tubing in and pull the tubing out. 

6.  Hang the Manifold Assembly on the 

mounting screws and tighten. DO NOT 

OVERTIGHTEN.

7.  Remove the wrapping from the  

In–Line Activated Carbon Post Filter. Slice 

the 

3

/

8

" Blue Polytube where it would be 

convenient to install and change the In–Line 

Filter. Make a clean straight cut to insure 

proper connections. The “Out” port on the  

In–Line Filter should be towards the faucet. 

Firmly press in the tubing. The fittings will 

grab the tubing and hold and seal it in place. 

Make sure the tubing is pressed all the way 

in to create a pressure tight connection.

E.  Position the Drinking Water Holding Tank 

and Make the Final Hose Connections. 

1.  Check the tank precharge pressure. Make 

sure it is between 5 to 7 psig. If not, use a 

bicycle hand pump or other pump to bring the 

pressure up to the 5 to 7 psig range.

2.  Pull the cap/plug off the top of the tank where 

the Tank Shut–Off should go. (Refer to Fig. 

1.)

3.  Wrap Teflon tape three times around the ¼" 

male outlet thread. Wrap in the direction of 

the threads (clockwise when looking down 

on the Holding Tank). The tape will act as a 

thread sealant. Screw on the Holding Tank 

Shut–Off Valve.

Содержание PURO-35T





















Отзывы: