PureTools PT-PMS-62S Скачать руководство пользователя страница 10

Страница: 10 / 64

User Manual

PT-PMS-62S

Audio Output

Audio Output

(1) Balanced audio (L+R) for

1.HDMI

output audio de-embedding

(1) Digital SPDIF audio (L+R) for

1.HDMI

output audio de-embedding

(1) Balanced audio (L+R) for

2.HDBT

output audio de-embedding

(1) Digital SPDIF audio (L+R) for

2.HDBT

output audio de-embedding

Audio Output Connector

(2) 5-pin terminal blocks, (2) To slink connectors

Frequency Response

20Hz – 20KHz, ±3dB

Max Output Level

2.0Vrms ± 0.5dB. 2V = 16dB headroom above -10dBV (316mV)
nominal consumer line level signal

THD+N

< 0.05% (-80dB), 20Hz – 20KHz bandwidth, 1KHz sine at 0dBFS
level (or max level)

SNR

> 80dB, 20Hz - 20KHz bandwidth

Crosstalk Isolation

> 70dB, 10KHz sine at 0dBFS level (or max level before clipping)

L-R Level Deviation

< 0.3dB, 1KHz sine at 0dBFS level (or max level before clipping)

Frequency Response
Deviation

< ± 0.5dB 20Hz - 20KHz

Output Load Capability

1KΩ and higher (Supports 10x paralleled 10KΩ loads)

Stereo Channel Separation

>70dB@1KHz

Noise Level

-80dB

Control Part

Control Port

(1) RS232, (2) RELAY 1-2, (1) IR EYE, (1) IR IN, (1) IR OUT, (1) TCP/IP,
(1) FIRMWARE

Control Connector

(3) 3-pin terminal blocks, (3) 3.5mm jacks, (1) RJ45, (1) Type-A USB

General

Transmission Mode

HDBaseT

Transmission Distance

HDBaseT Output:
1080P@60Hz ≤ 230 feet (70 meters),
4K@60Hz ≤ 131 feet (40 meters)

Bandwidth

18Gbps

Operation Temperature

-10

℃

~ +55

℃

Storage Temperature

-25

℃

~ +70

℃

Relative Humidity

10%-90%

External Power Supply

Input: AC 100~240V, 50/60Hz; Output: 24V DC 5A

Содержание PT-PMS-62S
































































Результаты поиска

Содержание PT-PMS-62S

Отзывы:

Похожие инструкции для PT-PMS-62S

Бренды по названию

Популярные бренды

PureTools PT-PMS-62S, Руководство пользователя

Результаты поиска

Содержание PT-PMS-62S

Отзывы:

Похожие инструкции для PT-PMS-62S

Бренды по названию

Популярные бренды