PureTools PT-PMS-62S Скачать руководство пользователя страница 8

Страница: 8 / 64

User Manual

PT-PMS-62S



Visually lossless video de-compression and compression for HDMI signals
transmission up to 40m at 4K and 70m at 1080P on HDBaseT output.



HDBaseT output support 24V PoC.



External balanced audio inputs can be embedded in two HDMI video inputs
respectively.



Provides two groups of audio outputs (balanced audio and digital SPDIF audio) for
audio de-embedding.



Supports MIX audio input and its volume control.



Supports HDMI output, HDBaseT output audio control.



Controllable via RS232 local and pass-through, IR local and pass-through, TCP/IP,
relay, CEC and on OSD.

1.2

Package List

Matrix Switcher



1x PT-PMS-62S 6x2 HDMI 2.0 Seamless Matrix Switcher



2x Mounting Ears with 6 Screws



4x Plastic Cushions



1x IR Remote



1x IR Receiver



3x 3-pin Terminal Blocks



5x 5-pin Terminal Blocks



1x Power Adaptor (24V DC 5A)

HDBaseT
Receiver



1x PT-HDBT-200-RX HDBaseT Receiver



2x Mounting Ears with 2 Screws



4x Plastic Cushions



1x 3-pin Terminal Block



1x User Manual

Note:

Please contact your distributor immediately if any damage or defect in the

components is found.

Содержание PT-PMS-62S
































































Результаты поиска

Содержание PT-PMS-62S

Отзывы:

Похожие инструкции для PT-PMS-62S

Бренды по названию

Популярные бренды

PureTools PT-PMS-62S, Руководство пользователя

Результаты поиска

Содержание PT-PMS-62S

Отзывы:

Похожие инструкции для PT-PMS-62S

Бренды по названию

Популярные бренды