Puretec NTR-E3 Series Скачать руководство пользователя страница 21

Страница: 21 / 24

NTR-E3 User Guide

Troubleshooting Guide

Troubleshooting Guide

PROBLEM

POSSIBLE CAUSE

SOLUTION

Regenerant being delivered to service

A. Low water pressure

A. Check incoming water pressure – water

pressure must remain at minimum of
25 psi

B. Incorrect injector size

B. Replace injector with correct size for

application

C. Restricted/kinked drain line

C. Check drain line for restrictions or debris, or

unkink drain line

Excessive water in regenerant tank.

A. Incorrect program settings.

A. Contact Puretec for assistance.

B. Plugged injector.

B. Clean/replace injector.

C. Loose/damaged drive cap assembly.

C. Tighten/replace drive cap assembly.

D. Leak from seal/spacer stack assembly.

D. Clean/replace spacer stack assembly.

E. Restricted/kinked drain line.

E. Check drain line for restrictions or debris,

or unkink drain line.

F. Plugged backwash flow controller.

F. Clean/replace backwash flow controller.

G. Plugged refill flow controller.

G. Clean/replace refill flow controller.

Valve fails to draw in regenerant.

A. Plugged injector.

A. Clean/replace injector.

B. Regenerant piston failure.

B. Clean/replace regenerant piston.

C. Leak in regenerant line.

C. Inspect regenerant line for air leak.

D. Restricted/kinked drain line.

D. Check drain line for restrictions or debris,

or unkink drain line.

E. Drain line too long or too high.

E. Shorten length and or height.

F. Low water pressure.

F. Check incoming water pressure – water

pressure must remain at minimum of 25
psi.

Water running to drain.

A. Power outage during regeneration.

A. Upon power being restored control

will finish the remaining regeneration
time. Reset time of day, replace battery
(CR2032).

B. Foreign material present in valve.

B. Remove drive cap, piston and spacer

assemblies. Clean and relubricate
components, assemble the valve and run a
manual backwash.

C. Leak from seal/spacer stack assembly.

C. Clean/replace spacer stack assembly.

D. Piston assembly failure.

D. Clean/replace piston assembly.

E. Loose/damaged drive cap assembly.

E. Tighten/replace drive cap assembly.

Содержание NTR-E3 Series

























Результаты поиска

Содержание NTR-E3 Series

Отзывы:

Похожие инструкции для NTR-E3 Series

Бренды по названию

Популярные бренды

Puretec NTR-E3 Series, Руководство пользователя

Результаты поиска

Содержание NTR-E3 Series

Отзывы:

Похожие инструкции для NTR-E3 Series

Бренды по названию

Популярные бренды