background image

16 

Installation & Operation Manual

Copyright © Puretec Pty Ltd 2018

Now programming is completed (if required) you are ready to start the system. 

1.  Fill the brine tank with ‘water softener’ salt to approximately half full. (salt 

not included). 

This will require approximately 60kg (this is only required initially). 

2.  Add approximately 15 litres of water to the salt in the brine tank. This is only required 

for the initial setup. 

 

Note: The water level will drop significantly after the first backwash, and may 
disapppear below the salt line. This is normal and no extra water will be required.

3.  Open the nearest tap downstream of the filter system (after the filter system).
4.  Allow water to flow through the system slowly, and allow all air to escape out of the 

closest tap. Wait until the water is flowing out of the tap and then increase the flow 
slowly up to full flow. Allow to run for 5 - 10 minutes.

5.  Close the opened tap and check for leaks.
6.  Conduct a full manual regeneration.
7.  Your system is ready for use.

MODEL

CAPACITY OF SYSTEM (L) WITH DIFFERENT HARDNESS LEVELS

100 mg/L

200 mg/L

300 mg/L

400 mg/L

500 mg/L

MUL35-E3

1967

983

655

491

393

MUL50-E3

2753

1376

917

688

550

MUL70-E3

3933

1966

1311

983

786

Regeneration

Start-up

Operation

E3 Valve 

(Regeneration Time: 90 mins)

This will adjust regeneration automatically once you have entered the correct hardness level 

in the programming section.

Содержание Multitrol MUL-E3 Series

























Отзывы: