background image

 

Whisper 30 integral Handbook   

 

 

 

 

 

 

4.3.1

 

Feed Pump, Pre- Filter and Hose connections

 

 

The Sea Water feed should be a marine grade Sea Cock, that you can close the Sea Cock individually  

 

Step 1   Connect the Sea Water intake with a re- enforced ½“ hose to the lower  hose barb at the valve at the 

Strainer. Connect the outlet of the Strainer with the intake of the feed pump. The upper connection of the 

Valve at the Strainer has to be connected with the outlet of the Carbon Filter. (FWF System) The inlet of 

the Carbon Filter must be connected with your boat pressure water.   

  

 

Step 2 Connect the outlet of the Feed Pump with the inlet of the red Pre-Filter.                 

 

 

 

Step 3 Connect the outlet of the Pre-Filter with the inlet of the ETD, marked 

with E.

 

 

 

Step 4  The outlet of the ETD is marked with 

S. 

Connect a ½” hose to the outlet over board. 

 

Note!! 

All connections past the Feed Pump have to be checked carefully, because there is already a 

pressure of 7-10 Bar. Tighten the hose cleats carefully and check for leaks by the first use. 

Use only reinforced water hoses which can stand the pressure of 10 Bar. 

 

                                       

---------

 

Pre – Filter installation completed ---------

 

 

 

 

 

 

 
 

 

 

 

 
 

 

 

 

 

 
 

 

 

 

 
 

 

 

 

 

 
 

Содержание Whisper 30

























Отзывы: