background image

 

1
 

 

 

The exclusive distributor of AMC products

 

 

 

MOUSE 07 

Dual Element Digital Motion Detector (dual 
pyroe microwave)

 

 

CODE 

MU07 

 

In accordance with the 
EN 50131-2-4 standard

 

MANUAL  EN

 

 

Edition: 2 from 07.03.2014

 

Supersedes: 1 from 10.02.2014

 

 

1. Introduction 

 

 

The  MOUSE  07  is  a  dual  element  digital  motion  detector  with  creep  zone  protection.  With  its 

advanced  signal  processing  algorithms  and  dual  detection  technology  (PIR  and  MW)  it  is  characterized  by 
very stable operation and low rate of false alarms. 

Z  Advanced  digital  temperature  compensation  enables  operation  over  a  wide  temperature  range.  The 

range of the MOUSE 07 detector is up to 14 meters with horizontal coverage exceeding 90 degrees. The area 
of the sensor operation is shown in the Figure 5. 
 

2. Installation of the detector 

 

The detector should  be  mounted by a qualified installer, holding relevant permits and licenses (applicable 

and required for a given country) for Intrusion Detection Systems. 

The latch system used in the enclosure of the detector eliminates the need for screw connections, so that 

the detector installation is simple and does not take much time.  

Follow the basic rules for the installation of Intrusion Detection Systems (pay attention, among others, not 

to soil or damage the pyroelement, do not point the detector towards strong light sources). 

The optimum mounting height of the MOUSE 07 detector is 2 meters).  

 
 
 
 
 
 

 

 
 
 

 

 

 

 

 

Fig. 1 

 Main view 

Fig. 2 

Inside view 

  

Содержание MOUSE 07







Отзывы: