Pulsar Blackbox Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 76

background image

Page 17

Operating the Controls

Operating the Controls

Operating the Controls

Operating the Controls

Display

The display on both the PC Programming Software (standard) and the Hand
Held Calibrator (optional) are identical, and when connected to the

blackbox

via the RS232 interface, provides information on the current mode of
operation.

Whilst in the Run Mode it will display the current level reading and its units
of measure, along with status messages with regards to the Transducer, Echo
reception  and  Fail  Safe  Mode.  When  in  the  Program  mode  the  display  is
used  to  read  information  on  the  Menu  System,  Parameter  Number  and
parameter  details  and  values,  which  can  be  entered.  During  Test  Mode  the
display is used to monitor the simulated level.

1234.56

mm

1)

Main Display

, 6 digit numeric display:

Run Mode

,

current measurement displayed, dependent on mode and

measurement unit's chosen, and value of Hot Key function selected.

Program Mode

, displays parameter number and values entered for

parameters.

Test Mode

,

displays simulated level.

2)

Auxiliary Display

, scrolling twelve digit alpha numeric display

Run Mode

, displays measurement units (P104), status messages on

signal and transducer, detail of Hot Key function selected.

Program Mode

,

displays Menu and Sub Menu headings, parameter

details and options.

1

2

«
...
21
22
23
24
25
...
»

Содержание Blackbox













































































Отзывы:

Нет отзывов

Похожие инструкции для Blackbox

Бренд: B&G Страницы: 2

Бренд: B&K Страницы: 9

Бренд: Watts Страницы: 2

Бренд: Hanbay Страницы: 18

Бренд: BADODOSECURITY Страницы: 8

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: Samson Страницы: 40

Бренд: Hach Страницы: 36

Бренд: Hach Страницы: 72

Бренд: NAPCO Страницы: 48

Magnum Alert 2600

Бренд: NAPCO Страницы: 68

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: Omega Страницы: 56

Бренд: Omega Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды