OPERATINg INSTRUcTION:
1. make sure all the units and the receivers are correctly switched
ON
2. Push the “
S
” button on the receiver then release it, the first channel led will illuminate continuously.
3. Select the desired channel* to register by a short pressure of
S
button on the receiver.
4. Once you’ve selected desired channel, trigger the unit to register it. the receiver and the unit will be now paired.
5. Repeat the above process to sync other units with the receiver.
*
in case the selected channel is already paired to another unit, the led will be lighting weaker than others. in this case you
may choose to completely erase the saved settings and re-sync all the units.
The complete Pulsar ADS Mini set is supplied already paired as a standard.
in case the receiver is not paired to the alarms, it’s necesarry to pair the bite alarms that it will be used, so that the receiver can register their unique
identification code. before starting this procedure, ensure all your bite alarms are switched ON, then proceed as follows:
Note:
the registration process can be disrupted if attempted in close proximity to other radio signals such as wireless routers
1.
Reset the paired code:
to erase the paired code in the receiver, press the “
S
” button in standby mode, select lEd indicator to choose the channel
you need erase, then press and hold “
S
” button till the light change from low light to high light.
2.
Reset all the paired code:
to erase all the paired code in the receiver, press and hold “
S
” button till the 4 lEd indicators flash at the same time,
then release the button. all the paired codes will be erased and the receiver is now completely reset.
ENcODINg INSTRUcTIONS WITh EASY SYNcRO SYSTEM:
1.
ON/OFF:
to activate the receiver switch the
ON/OFF
toggle on the back side of the receiver. the receiver will
check all channels and omit a sound. to switch the receiver Off, move the
ON/OFF
toggle in Off position, the
receiver will omit a short sound.
2.
Volume:
in standby mode, press and release the “
V
” button to adjust the volume. there are 6 different volume
settings available.
3.
Tone:
in standby mode press and release the “
T
” button to adjust the tone. there are 6 different tone settings
available. the “drop back” tone can’t be varied.
4.
Silent & Vibro Mode:
Pulsar adS mini receiver can be set to 3 different mode by pressing the dedicated button
on the front of the receiver (light & Sound – light & Sound & vibration – light & vibration)
5.
Last Record Alert:
in standby, press “
M
” button will indicate the last recorded alert received from transmitter.
6.
Run‘N Drop Bite Detection:
Pulsar adS mini receiver is able to detect running or drop back bites, in case of a
drop back bite the dedicated led will flash up. after detecting the bite the receiver will omit a fixed light for approx.
20”
7.
Audible & Visual Replication:
Each sound pulse and led flash from the bite alarm is replicated exactly at the
receiver, thus to eliminate strikes on false triggering caused by the wind and water movement.
8.
Low Battery Warning:
the Pulsars continuously monitor the battery voltage and detects its failing with audible/
visual warnings, when it occurs the unit will emit a sound and the red led flash for 1 second and it will continue
every minute till the battery is replaced. although the unit may continue to work for some time in this condition,
battery should be replaced at the earliest opportunity.
9.
Memory Function:
Pulsar will keep setting in memory. the last setting will be recalled even the unit is powered
Off.
REcEIvER
1.
ON/OFF:
to switch ON/Off the units press and hold the “
V
” button for 2 seconds approximately.
2.
Volume:
in standby mode press and release the “
V
” button to adjust the volume, the led indicator will flash
every pressure. there are 6 different volume settings available.
3.
Tone:
in standby mode press and release the “
T
” button to adjust the tone, the led indicator will flash every
pressure. there are 6 different tone settings available. the “drop back” tone can’t be varied.
4.
Sensitivity Adjustment:
in standby mode press and release the “
S
” button to adjust the sensitivity setting, the
led indicator will flash every pressure. there are 4 different sensitivity settings available, the highest sensitivity
level will make the unit trigger every small line movement.
5.
Induction Night-Light:
to Switch ON/Off the led night-light mode, press and hold for approx. 3 seconds the
“
T
” button. a long life and low consumption diode will help you to position your rod centrally onto alarm during
the night time. to switch off the Night-light mode, just simply keep press the “
T
” button, this will turn off only
the night-light mode option.
6.
Low Battery Warning:
the Pulsars continuously monitor the battery voltage and detects its failing with audible/
visual warnings, when it occurs the unit will emit a sound and the led flash for 1 second and it will continue
every minute till the battery is replaced. although the unit may continue to work for some time in this condition,
battery should be replaced at the earliest opportunity.
7.
Audible & Visual Replication:
Each sound pulse and led flash from the bite alarm is replicated exactly at the
receiver, thus to eliminate strikes on false triggering caused by the wind and water movement.
8.
Run‘N Drop Bite Detection:
Pulsar adS mini units are able to detect running or drop back bites, omitting differ-
ent sounds to immediately identify the bite. the unit will omit a fixed light for approx. 20 seconds after detecting
a bite.
9.
Power Out Socket:
allows K-Karp illuminated hangers to be powered directly from the unit. the illuminated
hangers will then light up when the Pulsar is activated.
MAIN UNIT
