No. Description Qty.
1.
Gun Body .................................1
2.
Nozzle Cap ...............................1
3.
Washer .....................................1
4.
Air Nozzle .................................1
5.
Snap Ring ................................1
6.
Fluid Nozzle..............................1
7.
Brass Ring ................................1
8.
Nylon Gasket ...........................1
9.
Packing Bushing ......................1
10. Washer .....................................2
11. Needle ......................................1
12. Spring .......................................1
13. Lock Nut ...................................1
14. Fluid Volume Control Knob ......1
15. Paint Cup Bushing ...................1
16. Trigger ......................................1
17. Trigger Pivot Pin .......................1
18. Needle Actuator Pin .................1
19. E-Clip .......................................4
20. Spray Regulator Nut ................1
No. Description Qty.
21. Spray Regulator Screw ............1
22. Teflon Seal ................................1
23. Spray Pattern Control Knob .....1
24. Screw .......................................1
25. Needle Valve Bushing ..............1
26. Teflon Ring ...............................1
27. Air Valve ...................................1
28. O-Ring ......................................1
29. Washer .....................................1
30. Needle Valve ............................1
31. Spring .......................................1
32. Air Inlet Bushing .......................1
33. Washer .....................................1
34. Air Volume Control Stem ..........1
35. Air Valve Stem Bushing ............1
36. Paint Cup Filter ........................1
37. Paint Cup Assembly .................1
38. Lid ............................................1
39. Air Regulator/Gauge Assembly 1
40. Wall Hanger ..............................1
3
4
PARTS LIST
REPLACEMENT PARTS AVAILABLE:
WARNING - DISCONNECT SPRAY GUN FROM AIR SOURCE BEFORE MAKING ADJUSTMENTS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This instruction manual is intended for your benefit. Please read and follow the safety, installation,
maintenance and troubleshooting steps described within to ensure your safety and satisfaction. The
contents of this instruction manual are based upon the latest product information available at the time of
publication. The manufacturer reserves the right to make product changes at any time without notice
.
SAFETY GUIDELINES / DEFINITIONS
WARNING: Read and understand this entire instruction manual before attempting to assemble, install, operate or maintain
this product. Failure to comply with the instructions may result in serious personal injury and/or property damage!
The following signal words are used to emphasize safety warnings that must be followed when using this product:
DANGER: Indicates an imminently hazardous situation
that, if not avoided, WILL result in death or serious injury.
WARNING: Indicates a potentially hazardous situation
that, if not avoided, COULD result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation
that, if not avoided, MAY result in minor or moderate injury.
NOTICE Indicates important information, which if not
followed, MAY cause damage to equipment.
Performance Tool repair kit: .......................................................... M710K
Step 3: Spray Pattern Controls Pattern
Shape
- The shape of the spray can be
adjusted from a round pattern to a flat
pattern by turning the pattern control knob.
Turning knob in, rounds the pattern. Turning
knob out, flattens the pattern.
Pattern Orientation - A flat or semi-round
spray pattern can be adjusted to any angle
from horizontal to vertical by turning the Air
Nozzle. Pattern is perpendicular to “ears”
on nozzle. That is, when the ears are horizontal
the spray pattern will be vertical and when
the ears are vertical the spray pattern will be
horizontal.
19
37
36
15
38
40
11
12
13
14
24
23
22
21
20
19
32
39
35
34
33
17
18
16
19
25
26
27
3
30
31
28
29
1
4
2
6
5
7
8
9
10
