manualshive.com logo in svg

PST Jets J600R, Инструкция по эксплуатации

Поделиться
Скачать
PST Jets J600R Скачать руководство пользователя страница 16

 

 

 

J600R Instruction Manual

 

 

Fuel System (cont) 

 

2.  The fuel tank must be free from foreign particles. 
3.  Use good quality turbo oil such as those in the picture above. 

2-stroke oil will cause 

serious damage to the engine and void your warranty.

 

4.  The fuel must be mixed with 5 percent turbo oil. For simplicity, mix five parts of oil to 

100 parts of kerosene. The J600 will tolerate mixture imperfections between 4-6%. 
Too little oil will shorten the bearings life due to higher temperature. Too much oil will 
reduce the engines performance due to unnecessary stress on the bearings. 

5.  We recommend that the fuel be mixed in gallon scales, as the mixing will be more 

accurate. Example: mix 1 quart of oil to 5 gallons (19 liters) of kerosene. Most turbo 
oil comes in quart cans, so mixing with 5 gallons of kerosene is simple. 

 

Gas System 

A. Internal Gas Canister 

 

 Gas Canister/Solenoid Valve & New Gas cartridge 

Filling the canister

 

 
1. 

2. 
3. 

4. 

5. 

6. 

7. 

8. 

A custom machined internal gas canister is provided with a quick connector 
attached. 
Use the blue 4mm tubing provided for gas connections. 
The two-way quick connect is connected to the gas solenoid valve and the one-way 
valve. 
The direction of the one-way valve is marked on the valve itself. "IN" direction is from 
the end with silver tape. The valve must be connected with the "IN" direction facing 
away from the canister to allow proper filling. In the pictures above the "IN" direction 
is plugged with an orange stopper. 
The tube ends should be pushed all the way into the connector/valve to avoid 
leakage. 
Fill the canister by connecting an external gas source (Propane/butane 70/30 mix) to 
the one-way valve "IN" direction. Point the external gas-filling tank (GAS CAN) down 
to let the liquid flow into the canister. 
Stop filling when the canister is 1/4 to 1/2 full. Since there is no visual indication, just 
approximate the filling amount. Very little is actually required for one successful auto 
start. The canister supplied is larger than required. From our tests, we can obtain 
more than 5 starts with one fill (3 starts with a new gas cartridge). 

Copyrights 

©

 PST Jets Co., Ltd.                                       - 

8

 -                                                       Version 1.5.3/2005

 

Disconnect the filling line carefully, as high pressure  propane is present in the line 
and will be forced out briefly. 

Safety:

 

Use towels or rags to cover the valve and keep 

your face and eyes away during disconnection. Do not smoke any where near your 
turbine at any time.

 

Содержание J600R













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды