manualshive.com logo in svg

PST Jets J600R, Инструкция по эксплуатации

Поделиться
Скачать
PST Jets J600R Скачать руководство пользователя страница 15

 

 

 

J600R Instruction Manual

 

 

Fuel System (cont) 

 
7.  Fueling is accomplished through the header tank into the main tank. Make sure that 

air bubbles are removed from the header tank. Air inside the fuel line will cause a 
flameout. Do not use flex tube or a clunk inside the header tank. The feed line 
should be geometrically centered in the header tank. See diagram C for more detail. 

8.  After the header tank is filled you can then fuel directly into the main tank for faster 

fueling. Your tanking system must be fitted with a fill tube to the main tank. 

9.  Ensure that you have safely wired and joined all line connections to prevent them 

from coming loose during operation. 

 

B. Fuel Pump 
 

 

 

 

Pump in direction 

Festo Ball Valve 

Use good filter

 

 
1.  Observe the pump fueling direction. Fuel goes in on the side marked by a small 

indention and out on the other side. 

2.  Use the clear 4mm tubing provided for fuel line connections. 
3.  Install ball valve between header tank and engine, either between the header tank 

and the pump (on suction side), or between the pump and engine (on pressure 
side). 

4.  Use a good gasoline filter between the fuel pump and the engine. It is better to have 

the filter behind the pump to avoid bubbles caused by suction/cavitations. 

5. Ensure that all wires and line connections are properly joined and attached to 

prevent them from coming loose during operation. 

 
C. Fuel and Oil 
 

 

Use clean & filtered fuel 

Turbo Oil 

Use clean fuel tank

 

 

1.  Use Jet A, Jet A1, or kerosene. Make sure that the fuel is clean and free from 

moisture and other forms of contamination. Water is heavier than fuel and will settle 
at the bottom of the container. 

Copyrights 

©

 PST Jets Co., Ltd.                                       - 

7

 -                                                       Version 1.5.3/2005

 

 

Содержание J600R













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды