PST Jets J600R страница 19 Скачать руководство пользователя | Manualshive

Страница: 19 / 44

background image

J600R Instruction Manual

Copyrights

©

PST Jets Co., Ltd. -

11

- Version 1.5.3/2005

Accessories (Cont)

D. Chargers

Sample of charger used

Sample of charger used

1. Use a high quality Ni-Cad/Li-Polymer charger that has good charging, discharging,

and conditioning cycle features. The supplied Ni-Cad battery can be quick or slow
charged.

2. Automatic charging is highly recommended.

3. Connect the appropriate charger connectors to the supplied charging cable taking

care that the polarity is correct.

E. Battery Checker

1. Use a good battery checker to check Rx battery

condition.

2. Rx battery’s health is important since the TEMS needs a

good radio signal to function properly.

3. ECU battery voltage can be monitored via the GDT.

«
...
17
18
19
20
21
...
»

Содержание J600R













































Отзывы:

Нет отзывов

Похожие инструкции для J600R

Бренд: Teryair Страницы: 13

Бренд: MTD Страницы: 32

Бренд: Forest-Master Страницы: 16

Бренд: Dietz Страницы: 10

Бренд: Dietz Страницы: 11

Бренд: Metronic Страницы: 24

Бренд: Lycoming Страницы: 38

Бренд: Electro motive Страницы: 287

Stagemaker SM10

Бренд: R & M Страницы: 71

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: Mitsubishi Heavy Industries Страницы: 220

Бренд: LinMot Страницы: 40

Бренд: Iveco Страницы: 74

Бренд: Mitsubishi Страницы: 42

Бренд: Eurotherm Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды