Proxima Ultralight SV1 Скачать руководство пользователя страница 7

Страница: 7 / 12

MODULE LEVEL

Ultralight SV1

101.670

SERVICE MANUAL

Proxima ASA

CONFIDENTIAL

ROBLEM

ROBABLE

AUSE

EMEDY

Fuse breaks instantly

Too much current to the unit

1. Wrong fuse value inserted on the

mains filter

(4)

(at F1)

2. DC power polarity to lamp power

supply inverted at the safety
switch

3. Defective lamp power supply

(6)

4. Defective mains filter

(4)

1. Replace fuse with correct value

(Schurter Type: SP 2.5A Fast 250 VAC)

2. Check DC power connection on safety

switch

3. Replace defective lamp power supply

4. Replace mains filter

Distorted noise from
speakers

Speaker(s)

defective (blown)

Replace housing complete with speakers

Unit shuts off while
being used

Possible overheating

1. Defective main fan(s)

(3)

2. Dirty dustfilter

3. Defective lamp (too much heat

dissipation)

4. Defective 100

Celcius Bi-metal

thermo switch

5. Defective main PCB controller

6. Lamp power supply

(6)

(ballast

unit) defective

1. Replace defective main fan/fanhouse

complete or remove obstructing object

2. Clean/replace dustfilter

3. Replace defective lamp

4. Replace fanhouse with fans and thermo

switch

5. Replace defective main PCB controller

and engine

6. Replace defective lamp power supply

Image is flickering or
appears to be unstable
in light intensity

Lamp light is flickering

1. Defective lamp

2. Dirty dustfilter

3. Defective lamp power supply

(6)

4. Defective Polysilicone engine

1. Replace defective lamp

2. Clean/replace dirty dustfilter (overheating

of lamp)

3. Replace defective lamp power supply

4. Replace defective Polysilicone engine

and main PCB controller

Colours break up

1. Bad connection between engine

and main PCB controller

2. User settings not allowed

1. Secure/fix flex cable connection

(See “Work Procedures” in section 7.1.2)

2. Execute Factory reset

White vertical line
appears far right in
picture

Synchronization error

Perform RESET on remote control or
projector panel

Содержание Ultralight SV1













Результаты поиска

Содержание Ultralight SV1

Отзывы:

Похожие инструкции для Ultralight SV1

Бренды по названию

Популярные бренды

Proxima Ultralight SV1, Руководство по обслуживанию

Результаты поиска

Содержание Ultralight SV1

Отзывы:

Похожие инструкции для Ultralight SV1

Бренды по названию

Популярные бренды