Proteus LDT-8850 Скачать руководство пользователя страница 45

Страница: 45 / 48

ERROR MASSAGE & TROUBLESHOOTING
E1 : It indicates no signal picked up for 15 seconds and the monitor stops.

Solutions : pls consult

Dealer

E2 : It indicates the problems of EEPROM IC chip. Either the ID code is incorrect or the data
accessed from the IC chip is wrong.

Solutions : pls consult

Dealer

E3 : It indicates that VR value is not change by 5 seconds.

Solutions:

a. Check the relay ( 12MBU-5 ), which controls the INC. The relay clicks while it is

functioning well. It indicates the INC signals in the yellow and green wires in the cable are

good.

b. Check the wires to the incline motor and see if they are open circuit, disconnected, or the

positive and negative are wrongly connected.

c. Calibrate the Incline function.
d. Check the incline motor to see if it is over-heated and the over-heating protection switch is

short circuit. If so, it will be functioning normal right after the motor is cool down.

e. If the above three solutions could not solve the problem, pls consult

Dealer

E4 : It indicates the changing VR values picked up are different.

Solutions : pls consult

Dealer

Содержание LDT-8850

















































Результаты поиска

Содержание LDT-8850

Отзывы:

Похожие инструкции для LDT-8850

Бренды по названию

Популярные бренды

Proteus LDT-8850, Руководство пользователя

Результаты поиска

Содержание LDT-8850

Отзывы:

Похожие инструкции для LDT-8850

Бренды по названию

Популярные бренды