Prostat PRS-801 Скачать руководство пользователя страница 31

Страница: 31 / 40

Rev. C / January 2012

PRS-812 Resistance Meter

OPERATIONAL NOTE

You may return the instrument to normal operations from the

RECORD/RECALL

mode at any time by pressing

RESET

b. 2nd Press

RECORD/RECALL

: LCD Displays

MIN

and the lowest recorded resistance value

saved in the Memory Register

c. 3rd Press

RECORD/RECALL

: Displays

MAX

and the highest recorded resistance value saved

in the Memory Register

NOTE

When displayed,

(Over Level) indicates a measurement greater than (>)

2.0x10

ohms, beyond the measurement capability of the PRS-812

d. 4th Press

RECORD/RECALL

: Displays

AVG

and the average of all recorded resistance values

saved in the Memory Register

NOTE

(Over Level) measurements greater than (>) 2.0x10

ohms are not included

in displayed average (AVG) calculation.

AVG

is the calculated average of all resis-

tance values less than (<) 2.0x10

ohms, rounded to the first decimal point.

e. 5th Press

RECORD/RECALL

: Returns PRS-812 System to normal operations

NOTE

RECALL

is not pressed, a fifth time

OOPS

will be displayed in the LCD when

TEST

is next pressed. To Clear

OOPS

, press

RESET

. The instrument will return to

normal operations.

VII. Instrument Maintenance

A. Calibration & Repair

1. Instrument Calibration should be performed annually

2. Only Prostat Corporation or their authorized instrument laboratory should perform PRS-812

calibration or repair.

3. Before shipping your instrument to Prostat Corporation for service, contact Prostat calibration

& customer service for a Return Material Authorization (RMA) tracking number by the follow-

ing means: See WARRANTY INFORMATION, below, for further instructions.

Содержание PRS-801









































Результаты поиска

Содержание PRS-801

Отзывы:

Бренды по названию

Популярные бренды

Prostat PRS-801, Руководство пользователя

Результаты поиска

Содержание PRS-801

Отзывы:

Бренды по названию

Популярные бренды