Prostat PRS-801 Скачать руководство пользователя страница 11

Страница: 11 / 40

Rev. C / January 2012

PRS-812 Resistance Meter

[2] RESISTANCE RANGE

SELECTION

Two Triangular Arrows Buttons, UP (

↑

) and DOWN (

↓

), select Resistance

Measurement Range in single orders of magnitude while in MANUAL or

AUTOMATIC/MANUAL

modes

[3] TEST VOLTS

Manual Selection of <10, 10 or 100 volts in

MANUAL

selects initial test

voltage.

MANUAL

Test Voltage & Resistance Limits are as follows:

@<10V:

0.1 to <1.0E+05Ω (0.1Ω - <100KΩ)

@ 10V:

1.0E+03 to <1.0E+09Ω (1KΩ - <1GΩ)

@100V:

2.0E+05 to <2.0E+14Ω (200KΩ - <200TΩ)

NOTE:

Optimal minium measurement in

MANUAL

using 100

volts is 2.0E+05.

[4] RECORD/RECALL

REC

is not displayed in the lower left corner of the LCD, pressing

RECORD/

RECALL

once turns Memory Register ON [

REC

will then be displayed in

LCD]. If

REC

is ON and measurement data is stored in memory, pressing

RECORD/RECALL

once will provide access to the memory register. Pressing

RECORD/RECALL

successively will calculate and sequentially display

Minimum [

MIN

], Maximum [

MAX

] and Average [

AVG

] of data stored in the

Memory Register. If memory is

and register contains stored data pressing

RECALL

will provide the following information:

First Press RECALL:

Provides access to data in Memory

NOTE: MEM

XX Flashes in LCD indicating number of data points in the

(↓)

and UP

(↑)

displays other data points and their respective position in the register is

shown in the

MEM

XX section of the LCD.

Second Press RECALL:

Displays MIN Data Point in Memory

Third Press RECALL:

Displays MAX Data Point in Memory

NOTE:

When displayed,

[Over Level] indicates a measurement greater

than (>) 2.0x10

ohms, which is beyond the measurement capability of the

PRS-812.

Fourth Press RECALL:

Displays

AVG

of all Memory Data Points

NOTE:

[Over Level] measurements [>2.0x10

ohms] are not included in

displayed average (

AVG

) calculation.

Fifth Press RECALL:

Returns System to normal operations

NOTE:

If in

RECALL

mode, pressing

RESET

will return the instrument to normal

measurement operations.

Содержание PRS-801









































Результаты поиска

Содержание PRS-801

Отзывы:

Бренды по названию

Популярные бренды

Prostat PRS-801, Руководство пользователя

Результаты поиска

Содержание PRS-801

Отзывы:

Бренды по названию

Популярные бренды