background image

PRS-UM-BTN-EN-Rev02-02.2019 

Mounting The Detector 

 
The detector should be mounted vertically as the sensor head pointing downwards. Detector 
has to be mounted such that the sensor's gas entrance area.  
 
The install location  

 

should be isolated from vibration, direct sun light and have temperature stability 

 

avoided external influences such as splashing water, oil, corrosive aerosols 

 

should have at least 30 cm free space beneath the sensor head to provide accessibility 
for calibration work. 

 

should be in air flow between possible leak or collection point and possible source of 
ignition. 

 
Prosense do not recommend to install detectors to : 

 

directly above a cooking unit, 

 

directly above a sink unit, 

 

close to an extractor unit, 

 

outdoor without protection against the rain, 

 

in places where temperature is outside the admissible operating range, 

 

in corrosive environments, 

 

inside air vents. 

 

in environments where silicon can be found. 

 
The Prosense detector has an integrated mounting screw holes on the body. The correct 
mounting position is given in Diagram 3: 
 

 

Diagram 3: Mounting holes on body 

Mounting hole 

Mounting hole 

Mounting hole 

Содержание BTN Series

















Отзывы: