Prosense BTN Series Скачать руководство пользователя страница 15

Страница: 15 / 16

PRS-UM-BTN-EN-Rev02-02.2019

to Span button till the level reaches the necessarly value. Once the span calibration
completed remove the jumper and put as a spare on to detector board.
Important: Never put jumper on both S+ and S- pins and press any button.

Diagram 11: Calibration buttons and pins

General Specification

BTN Series Detector Electrical Specifications:

Input Voltage Range

12 to 20VDC (16VDC nominal)

Max Power Consumption 0.96 Watts at 16VDC - normal condition

1.60 Watts at 16VDC - alarm and fault condition

Terminals

4 x 2 x screw terminals suitable for wire diameter 1.5mm2 to 2.5mm2

Relays

3 x (1A 30VDC, 0.5A 125VAC, 0.3A 80VDC).

Non-selectable: normally open and de-energized

Communication

RS485, Modbus RTU

Sensor

Catalytic

Table 2: BTN Series detectors electrical specifications

Detector Body Specifications:

Material

Plastic (black)

Weight

Plastic buat: 230g (with Sensor Header)

Mounting

Wall mounting

Entries

PG11

Table 3: Detector body specifications

Environmental:

IP Rating

IP54 (plastic buat)

Operating Temperature

-10ºC to +50ºC / 14ºF to +120ºF

Operating Humidity

Continuous 20-90%RH (non condensing)

Operating Pressure

90-110kPa

Storage Conditions

-10°C to +50°C (14°F to +120°F)

Table 4: Environmental specifications

Span (S) and Zero (Z) buttons

Span (S+ , S-) and Zero (Z) pins

Содержание BTN Series

















Результаты поиска

Содержание BTN Series

Отзывы:

Похожие инструкции для BTN Series

Бренды по названию

Популярные бренды

Prosense BTN Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BTN Series

Отзывы:

Похожие инструкции для BTN Series

Бренды по названию

Популярные бренды