PMX Series Mixer
8
STEREO AUX RETURN 1
The STEREO AUX RETURN 1 connectors generally serve
as the return path for the effects mix generated using the post-
fader aux send. This is where you connect the output signal
of the external effects device. If only the connector is used,
the AUX RETURN automatically operates in mono.
If you wish to use the internal effects processor, no connectors should be plugged into
STEREO AUX RETURN 2.
In this instance, the FX control of the channel being used as an effects return should be
turned fully counterclockwise, otherwise feedback problems could occur!
STEREO AUX RETURN 2
You can also use these connectors as additional
line inputs.
The STEREO AUX RETURN 2 connectors serve as the return path for the effects mix generated using
the FX control. If these connectors already function as additional inputs, you can route the effects signal
back into the console via a different channel, with the added benefit that the channel EQ can be used to
adjust the frequency of the effects signal.
2.3.3 Stereo aux return connectors
Fig. 2.8:
Stereo aux return connectors
LEFT
/MONO
RIGHT
1
2
RETURNS
STEREO AUX
STEREO AUX RETURN 1
2.3.4 Stereo aux return
Fig. 2.9: Stereo aux return controls
0
8
0
8
1
2
0
8
1
STEREO AUX RETURNS
MAIN MIX
ALT 3-4
TO AUX
SEND 1
8
8
8
FX
STEREO AUX RETURN 1 is a stereo control which
determines is used as effects return, you can add the effects
signal to any ”dry” channel signal .
In this instance, the effects device should be set
at 100% effect.
Monitor mix with effect
STEREO AUX RETURN MON
The STEREO AUX RETURN MON control has a special function: it can be used to add an effect to a
monitor mix.
In this instance, the effect device should be set up as follows: AUX SEND 2 is connected to the L/Mono
input of your effects device, while its outputs are connected to STEREO AUX RETURN 1. Connect the
amplifier of your monitor system to AUX SEND 1. The AUX SEND 1 master control determines the volume
of the monitor mix.
PMX Series Mixer
9
You can now use the STEREO AUX RETURN MON control to adjust the level of the effects signal
routed to the monitor mix.
The STEREO AUX RETURN 2 control determines the level of signals fed into the AUX RETURN 2
connectors which are routed to the main mix.
STEREO AUX RETURN 2 (FX)
MAIN MIX/ALT 3-4
The MAIN MIX/ALT 3-4 switch routes the signal connected to STEREO AUX RETURN 2 to either main
mix (not pressed) or submix (Alt 3-4, pressed).
2-TRACK OUTPUT
These connectors are wired in parallel with MAIN OUT and carry the main mix signal (unbalanced).
Connect the 2-TRACK OUTPUT to the inputs of your recording device. The final output level can be
adjusted via the high-precision MAIN MIX fader.
If you connect a compressor or a noise gate after the 2-track output, the faders will probably
not be able to create a satisfactory fade-out effect.
2-TRACK INPUT
The 2-TRACK INPUT RCA connectors are provided for
connecting a 2 track machine (e.g. DA T recorder). They
can also be used as stereo line input. Alternatively, the
output signal of a second MX Series Mixing can also be
connected. If you connect a hi fi amplifier with a source
selection switch to the
INPUT, you can easily
2-TRACK
switch between additional sources (e.g. Cassette recorder,
CD player, etc.).
2.3.5 Tape input/tape output
Fig. 2.10: 2-track connectors
INPUT
L
OUTPUT
2TK TO MAIN MIX
L
R
R
Similarly, the ALT 3-4 switch routes the signal from the
Alt 3-4 bus to the same path for monitoring purposes.
ALT 3-4
The TRACK switch routed, the signal from the TRACK
IN connectors to the level metre, the CONTROL ROOM
OUT outputs and the PHONES connector----this is a simple
way to check recorded signals via monitor speakers or
headphones.
2-TRACK
2.3.6 Level meter and monitoring
Fig. 2.11: Control room/phones section,
level meter
-
+15
8
3
4
MODE
SOLO (NORMAL)
PFL (LEVEL SET)
L
R
MAIN SOLO PFL
MAIN MIX
ALT 3-4
2-TRACK
PHONES/CTRL R
SOURCE
2TK TO MAIN MIX
POWER
+48 V
CLIP
10
5
2
0
2
5
20
