ProMinent DULCOMETER D1C Type D Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 28

ProMinent DULCOMETER D1C Type D Скачать руководство пользователя страница 3

3

Page

1

Device Identification / Identity Code .................................................................................................... 2

2

General User Information ...................................................................................................................... 3

3

Device Overview / Controls ................................................................................................................... 4

4

Functional Description .......................................................................................................................... 5

5

Display Symbols .................................................................................................................................... 6

6

Operation diagram ................................................................................................................................ 7

7

Restricted Operating Menu ................................................................................................................... 8

General Layout ............................................................................................................................. 8

Description ................................................................................................................................... 9

8

Complete Operating Menu .................................................................................................................. 13

Overview ..................................................................................................................................... 13

Description ................................................................................................................................. 14

9

Fault/Remarks/Troubleshooting ......................................................................................................... 28

General User Information

These operating instructions describe the technical data and function of the series DULCOMETER

®

D1C

controller, provide detailed safety information and are divided into clear steps.

IMPORTANT

• Please observe the parts of these operating instructions applicable to your particular

version! This is indicated in the Section “Device Identification / Identity Code”!

• Correct measuring and metering is only possible in the case of impeccable operation of

the sensor. The sensor has to be calibrated / checked regularly!

NOTE

A form “Documentation of controller settings type D1C” is available under
www.prominent.com/documentation_D1C for the purpose of documenting the controller
settings.

2

General User Information

BA_DM_138_09_06_GB.p65

21.09.2006, 11:22 Uhr

3

«
1
2
3
4
5
...
»

Содержание DULCOMETER D1C Type D





























Отзывы:

Нет отзывов