background image

PACKAGE CONTENTS

2

HARDWARE CONTENTS

1. Canopy
2. Canopy Cover
3. Mounting Bracket Screw 

(x4)
4. Mounting Bracket
5. Downrod
6. Downrod Clip
7. Downrod Pin
8. Yoke Cover
9. Set Screw (x2)
10. Closemount Screw (x3)
11. Motor Assembly

12. Switch Housing
13. Switch Housing Screw (x3)
14. Switch Housing Cap
15. Light Kit
16. Light Cage (x3)
17. Blade Arm (x5)
18. Blade (x5) 
19. E26-base LED Bulb (x3)
20. Owner’s Manual
21. Hardware Kit
22. Motor Screw (x10)
23. Light Cage Screw (x12)

24. Blade Screw (x15)
25. Blade Washer (x15)
26. Wire Connector (x3)
27. Pull Chain Extension (x2)

28. Secondary Support Screw
29. Support Washer
30. Secondary Spring Washer
31. Blade Balancing Kit

Unpack your fan and check the contents.  You should 

have the following items:

PACKAGE CONTENTS

HARDWARE CONTENTS

Note: 

Some extra hardware has been included. The quantity 

listed above is the number required for installation.

HARDWARE CONTENTS

25

28

29

27

26

TOOLS REQUIRED 

(not included)

Tools required for assembly:

 Electrical tape, Phillips Screwdriver, Pliers, Safety Glasses, Step Ladder, Wire Cutters 

and Wire Strippers

Helpful Tools:

 AC Tester Light, Tape Measure, and Wiring Handbook

Hardware Kit

 

Owner’s

Manual

30

31

12

11

9

8

10

7

6

5

4

16

19

20

21

24

22

23

17

18

13

3

14

15

2

1

Содержание 50650













Отзывы: