13
14
All ProTournament
elite Battery Chargers are designed to be permanently mounted on-board,
and should be mounted with extruded fins placed horizontally.
Always mount your ProTournament
elite in a compartment area that can be properly ventilated
during use.
Do NOT mix battery types on-board. All batteries should be of the same age and in good
operating condition.
Do NOT make any electrical connections to the ProTournament
elite or batteries until the following
steps are completed:
10 Easy to Follow Installation Steps:
1. Select a mounting location that allows for free air ventilation with a minimum of 8 inches of
clear unobstructed space around and in front of the battery charger. Open all battery and engine
compartments and ventilate for at least 15 minutes before starting the installation of the charger.
Confirm all battery cables can reach each of the batteries.
Do not install charger on carpeted, upholstered, vinyl, or varnished areas. Be sure to place the
ProTournament
elite in an accessible area where all indicators are viewable. Install this unit on
a hard surface.
Note: For installations requiring an extension of the DC battery charger cables, please call or visit
your retailer or dealer to purchase ProMariner’s 5 foot or 15 foot battery charger DC cable extenders.
Our innovative cable extenders are properly fused and do not require any cutting or stripping of
wires. If you have any problems locating this accessory call ProMariner at 1-800-824-0524.
2. Using the ProTournament
elite or the enclosed paper template, mark the position of each
mounting hole. Ensure the mounting screws will not puncture or protrude into a live well, a fuel
or oil tank or the bottom of the boat.
3. Using a 1/8" drill bit, drill pilot holes in the (4) marked locations as described in step 2.
Apply a silicon sealer in each of the mounting locations to waterproof the screw holes.
4. Position the charger over the mounting holes and secure with a power screwdriver
by installing 4 stainless steel #10 screws. (mounting screws included).
For aluminum boat installation we recommend installing your ProTournament
elite Charger on a
wood or fiberglass panel and not directly on the aluminum hull.
1/8" pilot hole w/ silicon sealer
IMPORTANT NOTICE
· Maintain an obstruction-free area of 6 inches
around the product.
· Prior to mounting, confirm mounting surface has
adequate strength and thickness.
· Check for electrical or fuel lines on or behind surface.
· Consult boat manufacturer for suggested mounting
location or procedure.
Installation
Comm LEDs
Comm ID
1
1
2
2
3
3
4
4
Comm LEDs
Comm ID
5
5
1 + 5
6
2 + 5
7
3 + 5
8
Installation
Com ID Selection (For Global AC Input Models Only)
Your battery charger is equipped with a CZone/NMEA2000
®
communication interface. If you are
using
more than one
ProTournament
elite to charge your system
in the same CZone/NMEA2000
®
network
, the Com ID must be set to be different for each ProTournament
elite charger. If you are
using
only one
ProTournament
elite, you
do not
need to change the Com ID.
To set the Com ID, follow the 3 steps below:
1. Press and hold the com button for 3 seconds and release. The comm ID number and
LED will be blinking indicating that the Com ID can be set.
2. Press the com button to change the selected Com ID. Repeat the button press until
the desired Com ID is selected.
3. Press and hold the com button for 3 seconds to save the selected Com ID in the charger.
CZone (Global models only)
CZone Communication
The CZone interface communicates battery chemistry, charge mode, real time charging voltage,
amperage and fault status. See examples below:
For a complete communication list, please visit www.promariner.com/ProTournament-Elite-3-Global
See CZone configuration tool manual for setup.
Installation
MONITORING
Engine Start Battery
11.89V
9.5A
ALL
Trolling Motor Battery 1
11.89V
9.5A
DC MONITORING
Trolling Motor Battery 2
11.77V
11A
Trolling Motor Battery 3
11.77V
11A
Electronics Battery
11.77V
11A
PROTOURNAMENT
CHARGER
ON
/
BULK
Engine Start Battery
11.89V 9.5A
Electronics Battery 1
11.77V 11A
Trolling Motor Battery 3
11.77V 11A
Trolling Motor Battery 2
11.77V 11A
Trolling Motor Battery 1
11.89V 9.5A
Note: The CZone interface reports the chargers voltages and currents.
