PROFIX QT6201, Руководство по эксплуатации

Страница: 5 / 40

5
e) Power tools require maintenance. Check power tools for technician.
concentricity or jamming of moving parts, any cracks and all
d) Prior to starting operation of the device one has to
other factors affecting the power tool work safety. If any
thoroughly inspect the area where the machine is to be used
damage to the power tool is detected, it should be repaired
and remove all hard things that may damage the chopping
before use. Improper power tool maintenance is a reason for many
mechanisms used to disintegrate swept material (e.g. stones,
accidents.
tins, pieces of glass, porcelain or metal).
f) Cutting tools should be sharp and clean. Keeping sharp cutting
e) Do not use the device to collect hot, glowing or burning
edges in good condition reduces the risk of jamming and facilitates
material (e.g. cigarette butts, glows of fossil) as well as do not
operation.
target the blown air to such things.
g) Power tools, equipment, working tools etc. should be used
f) Do not use the device nearby flammable liquids or gases.
according to this user's manual taking into account
Otherwise a hazard of a fire or an explosion may exist.
operating conditions and the work to be done. Misusing a
g) Do never use the device at rain, poor weather or in wet
power tool can result in dangerous situations.
environment. Work only at daylight time or with very good
h) At low temperatures and after a long brakes in operation it is
electric illumination.
recommended to turn the power tool to operate it with no
h) The device can be used in the sweeping mode only when the
load for a few minutes to provide proper grease distribution
waste bag is installed. The waste bag should be emptied with
inside its driving mechanism.
sufficient frequency and inspected for possible wear or damage.
i) Use soft, damp (cannot be wet) cloth and soap to clean power
i) The device is not suitable to suck in humid or wet materials
tools. Do not use petrol, solvents and other agents that may
or liquids. It is necessary to avoid collecting humid materials (leaves,
damage your equipment .
dirt) as they may cause clogging of the chopping chamber, which leads
j) Power tools can be stored/carried after making sure that all
to drop of the machine efficiency. If it happens the device must be fully
moving components are locked and protected against
disassembled and cleaned. Such an operation must be carried out by a
release with original devices intended for this purpose.
qualified person and is not covered by the scope of warranty.
k) Store power tools in a dry, dust and water-protected place.
j) Do never use the device with bare feet or in open sandals.
l) Carry your power tool in its original packaging to provide Working with the device is only allowed in solid shoes on
protection against mechanical damage.
antiskid soles and long trousers. Always wear protecting glasses
or goggles and take care of your ears by use of appropriate hearing
WARNING! General warnings regarding the use of
protectors.
power tools.
In case of working in a dusty environment put on appropriate masks to
Repair :
protect the upper part of the respiratory tract.
k) Avoid wearing loose clothes or jewellery as these may be
seized by the suction pipe.
Persons with long hair should keep it covered with e.g. a cap.
l) Keep finger and feet far away from the suction pipe and the
bladed wheel.
Do not push any objects into the suction pipe due to a
hazard of injuries.
m) Operators should be always confident that they stay
steadily, in particular when they work on a sloped ground.
Always hold the tool with two hands and work with appropriately
adjusted and fastened shoulder belt that helps to carry the appliance
up. Do never switch the tool on if it is in the upside down position or in
WARNING! GARDEN LEAF SWEEPER /BLOWER,
any other position inappropriate for operation.
supplementary safety precautions:
n) When the tool is in operation do never allow third persons to
a) The appliance can be used only when is fully assembled. It is
come close, in particular children or pets. Operators shall be
not permitted to operate the appliance by minors below the age of 16.
Also people who have not read this User Manual and have not sufficient
held responsible for any accidents or hazards to third
skills to use of the device are not allowed to operate the machine. persons and their property. The mentioned persons should be kept
within the distance not less than 6 meters form the working place. Do
b) To eliminate possible hazards to operators it is mandatory to
never aim the tool towards such persons when it is in operation, in
periodically check whether the device is in sound technical
particular do not blow the air stream to eyes or ears. Pay attention to
condition. Prior to commencement of the device operation one has to
open windows nearby – the blown material may be thrown away to
tighten all the loosened bolts, screws and nuts. Worn or damaged parts
undesired directions.
shall be replaced with new ones.
o) Always unplug the device from an electric outlet under the
c) Make sure that the device can be switched off immediately
following circumstances:
under emergency circumstances. Do never use the device if
- prior to removing jammed or seized material;
it cannot be switched on and off with use of the mains
switch.
Faulty switch must be handed over for repair by a qualified - prior to any inspection, starting cleaning or commencement any
a) Power tools can be repaired by competent persons only who
use original spare parts.
It will provide safe operation for the power
tool.
b) If a fixed power cord is damaged, to avoid risks it should be
replaced by power tool manufacturer or in a specialty repair
shop or by a qualified person.
WARNING!
While operating power tools it is necessary to observe basic
work safety rules to avoid fire, electric shock or mechanical
injury.