Prochem EVEREST 408 Скачать руководство пользователя | Manualshive

Страница: 21 / 59

background image

19

Installation

Fuel Supply & Return Line Installation

(Underneath Van)

1.

Spray the inside of the supplied 90 degree plastic barbed fitting with water displacing lubricant. Push plastic
fitting onto the return tube on filler neck adapter tube until fitting securely snaps into place.

2.

Measure and cut a length of 5/16" fuel hose and connect to the plastic barbed fitting on the return tube of the
filler neck adapter tube. Connect other end of hose to 1/4 x 5/16 brass hose adapter and attach adapter to 1/4"
fuel hose from electronic fuel pressure regulator. Fasten securely using supplied hose clamps.

3.

Install (1) 1/8P x 5/16 push-on hosebarb fitting on to the bulkhead adapter.

4.

Measure and cut a length of 5/16" fuel hose and connect between the outlet side of the electronic fuel pressure
regulator and the 1/8P x 5/16 push-on hosebarb fitting at the bulkhead. DO NOT USE HOSE CLAMPS AT
THIS CONNECTION.

NOTE: Fuel tap kit installation instructions are found with appropriate fuel tap kit. Refer to Fuel Tap Kit
Information Sheet (86349940)

CONNECTOR

CHECK VALVE

5/16" SUPPLY HOSE

HOSE MOUNTING CLAMP

FRONT OF VAN

BULKHEAD

BUSHINGS

ELECTRICAL CORDS

PUMP ASSEMBLY

ELECTRICAL FUEL

USE AS NEEDED

5/16" SUPPLY HOSE

FUEL SUPPLY

RETURN TO VEHICLE

FROM VEHICLE

FUEL SUPPLY

FUEL FLOW

FUEL FILTER

1/4" RETURN HOSE

86411100 Manual Operators - Everest E-Idle Prochem

«
...
19
20
21
22
23
...
»

Содержание EVEREST 408




























































Отзывы:

Нет отзывов

Похожие инструкции для EVEREST 408

Бренд: Martin Страницы: 50

Бренд: Practical Systems, Inc. Страницы: 2

Бренд: Sanitas Страницы: 20

Бренд: DS Produkte Страницы: 4

Бренд: DS Produkte Страницы: 4

Бренд: DS Produkte Страницы: 36

Бренд: EMAG Страницы: 36

Бренд: K&M Страницы: 36

Бренд: Workzone Страницы: 17

Бренд: HOFFEN Страницы: 32

Бренд: Metabo HPT Страницы: 40

TankJet 9 Series

Бренд: Spraying Systems Co Страницы: 4

Бренд: Spraying Systems Co Страницы: 12

Бренд: Grundig Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды