background image

English

© 2007 Proceq SA 

Measuring Process 

19

Scanning the measuring area with display of the 
concrete covers

Key:
6 Speed display. The flow 
  bar must be within the
  scale.
7 Smallest measured 
  concrete cover
8 Current concrete cover
9 Symbol for travelling and
  scanning

6      7          8      9

Fig. 5.16  Measuring area after measuring

•  If the rebars of the first layer run in a vertical direction
  as shown in Fig. 5.14, the travel paths must
  be positioned horizontally with the selected grid spa-
  cing in direction y. Move the mobile probe along these
  paths. In Fig. 5.16, pos. 7, the smallest concrete cover
  measured in a grid field is displayed and stored auto-
  matically as grey scale.
•  After having finished one row, press the 

 key. The 

  cursor jumps to below the last field and the arrow
  direction changes automatically.

 

After every manual or automatic change of the

  arrow direction, RESET must be pressed. See

 

also «RESET process», page 10.

•  Once the second row at the edge of the measuring
  area (y-axis) is completed, the cursor jumps to below
  the last field and the arrow direction changes automa-
  tically.
The indicating device operates in the same way if the 
travel paths are positioned vertically, i.e. if measuring is 
performed in direction y.
•  If a hindrance prevents the measurements, you can
  shift the cursor by the size of the obstacle.
•  Individual values can be deleted by positioning the 
  cursor on the respective value and pressing the
  PRINT/STORE key for two seconds.
•  You can subsequently expand the object opened last in 
  the x and y-direction on new pages comprising 240
  measured values.
•  For all previous objects, measured values can only be
  entered in pages that are not yet full.
•  If the measurement cannot be started in the top left
  corner (x and y = 0) you can move the cursor to the
  starting position using the corresponding arrow keys.
•  If you want to reserve pages that will be needed later,
  each page has to be selected separately. To confirm
  the reservation you can set a grey scale symbol in the
  second row using the PRINT/STORE key. The grey
  scale symbol can be overwritten or deleted at any time.

Содержание Profometer 5+































Отзывы: