background image

English

© 2007 Proceq SA 

Measuring Process 

17

5.5 

Measure with Grid

Model SCANLOG only
This function displays concrete covers over a large area 
in grey scale or colour shades. The smallest concrete 
cover measured in a grid field is displayed.

Settings

See also «Settings», page 6.
•  Enter the bar diameter of the first layer.
•  Enter the object number.
•  Enter the bar spacing under the menu option 
«Corrections» 

  → «Neighb. Bar Corr.» if the correction is required.

The «2-Layer Correction» can not be used by this 
function.
•  Select the size of the grid field («MENU» 

 «Basic

  setups» 

 «xy-grid»).

The grid should usually be greater than the division of 
the first layer (e.g. +50 %) to ensure that at least one 
rebar is within a grid field.

•  Set the range in which the concrete covers are to be
  displayed in grey scale («MENU» 

 «Basic setups»

 

 «Display»).

Change the grey scale range to improve the contrast of 
the displayed object (see Fig. 5.12).

Fig. 5.12  Adjusting grey scale range

The range can be adjusted as desired even after 
measuring.
•  Select the «Measure with Grid» function.
•  Pressing the START key calls the measuring display:

Fig. 5.13  «Measure with Grid» measuring display

Содержание Profometer 5+































Отзывы: