background image

Safety

2

READ AND FOLLOW 

SAFETY INSTRUCTIONS!

This is the safety alert symbol.

When you see

this symbol on your pump or in this manual,

look for one of the following signal words and be
alert to the potential for personal injury.

warns about hazards that 

will 

cause

serious personal injury, death or major property
damage if ignored.

warns about hazards that 

can 

cause

serious personal injury, death or major property
damage if ignored.

warns about hazards that 

will 

or 

can

cause minor personal injury or property damage if
ignored.
The label 

NOTICE 

indicates special instructions

which are important but not related to hazards.

Carefully read and follow all safety instructions in
this manual and on pump.

Keep safety labels in good condition. 
Replace missing or damaged safety labels.

RULES FOR SAFE

INSTALLATION AND

OPERATION

Read the Owner’s Manual and Rules for Safe
Operation and Installation Instructions carefully.
Failure to follow these Rules and Instructions could
cause serious bodily injury and/or property dam-
age.
Install system according to local codes.
Always test water from well for purity before using.
Check your local health department for testing 
procedure.
Before installing or servicing your tank, BE SURE
pump electric power source is disconnected.
BE SURE your pump electrical circuit is properly
grounded.
Remove bleeder orifices, air volume controls or
other air charging devices in existing system.

To prevent possible serious or fatal

injury and/or damage to equipment, system pres-
sure must be less than 100 pounds per square inch
(PSI) under any circumstances. Failure to follow
this instruction can result in tank blowup. If sys-
tem discharge pressure can exceed 100 PSI, install
a relief valve capable of passing the full pump vol-
ume at 100 PSI.

Hazardous pressure. Read owner’s

manual before attempting to install, operate, or
service this tank. To avoid possible equipment fail-
ure, severe injury, and property damage, do not
allow pump, tank, or piping system to freeze.

LIMITED WARRANTY

PENTAIR WATER warrants to the original consumer purchaser (“Purchaser” or “You”) of the products listed below, that they will be free
from defects in material and workmanship for the Warranty Period shown below.

Product

Warranty Period

Water Systems Products — jet pumps,

whichever occurs first:

small centrifugal pumps, submersible pumps

12 months from date of original installation, or

and related accessories

18 months from date of manufacture

Signature 2000

®

Fibrewound Tanks

5 years from date of original installation

Pro-Source Plus

TM

Fibrewound Tanks

5 years from date of original installation

Pro-Source

TM

Steel Pressure Tanks

5 years from date of original installation

Pro-Source

TM

Epoxy-Lined Tanks

3 years from date of original installation

Sump/Sewage/Effluent Products

12 months from date of original installation, or
18 months from date of manufacture

Our warranty will not apply to any product that, in our sole judgement, has been subject to negligence, misapplication, improper
installation, or improper maintenance. Without limiting the foregoing, operating a three phase motor with single phase power
through a phase converter will void the warranty. Note also that three phase motors must be protected by three-leg, ambient com-
pensated, extra-quick trip overload relays of the recommended size or the warranty is void.

Your only remedy, and PENTAIR WATER’s only duty, is that PENTAIR WATER repair or replace defective products (at PENTAIR
WATER’s choice). You must pay all labor and shipping charges associated with this warranty and must request warranty service
through the installing dealer as soon as a problem is discovered. No request for service will be accepted if received after the
Warranty Period has expired. This warranty is not transferable.

PENTAIR WATER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHAT-
SOEVER.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE FOREGOING WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION EXPRESSLY PROVIDED HEREIN.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on the duration of an
implied warranty, so the above limitations or exclusions may not apply to You. This warranty gives You specific legal rights and You
may also have other rights which vary from state to state.

This warranty supersedes and replaces all previous warranty publications.

PENTAIR WATER

293 Wright St., Delavan, WI  53115

TPS series tanks are identical

to PS series tanks except for

color. All parts are the same.

Содержание PS119-TR50

























Отзывы: