PROBLEM: The walking belt is off-centre or slips when walked on
SOLUTION:
a. If the walking belt is off-centre, first remove the key and
UNPLUG THE POWER CORD
.
If the walking belt has
shifted to the left,
use the allen wrench to turn the left
rear roller bolt clockwise 1/2 of a turn;
if the walking belt
has shifted to the right,
turn the bolt counterclockwise
1/2 of a turn. Be careful not to overtighten the walking belt.
Plug in the power cord, insert the key and run the treadmill
for a few minutes. Repeat until the walking belt is centred.
b. If the walking belt slips when walked on, first remove the
key and
UNPLUG THE POWER CORD
. Using the allen
wrench, turn both rear roller bolts clockwise 1/4 of a turn.
When the walking belt is correctly tightened, you should
be able to lift each side of the walking belt 5–7 cm (2–3 in.)
off the walking platform. Be careful to keep the walking
belt centred. Plug in the power cord, insert the key, and
walk on the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
PROBLEM: The displays of the console do not function properly
SOLUTION:
a. Remove the key from the console and
UNPLUG THE
POWER CORD.
With the help of a second person,
carefully tip the Base (109) down as shown. Remove
the four Long Belly Pan Screws (121). Note: A phillips
screwdriver with at least a 5” shaft is required.
With the help of a second person, carefully raise the
Upright (82) as shown. Carefully pivot the Hood (39)
off.
Locate the Reed Switch (24) and the Magnet (18) on
the left side of the Pulley (120). Turn the Pulley until
the Magnet is aligned with the Reed Switch.
Make
sure that the gap between the Magnet and the
Reed Switch is about 3 mm (1/8 in.).
If necessary,
loosen the Screw (25) and move the Reed Switch
slightly. Retighten the Screw. Reattach the Hood, and
run the treadmill for a few minutes to check for a cor-
rect speed reading.
18
24
25
Top
View
3 mm
120
121
121
109
a
39
82
a
b
6
3/4” Screw (6)–16
Internal Star
Washer (72)–6
1 1/4” Bolt (104)–4
Wheel Bolt (107)–2
Wheel Nut (21)–2
2” Silver Screw (93)–2
1 1/4” Screw (92)–2
1” Bolt (71)–2
For help identifying the assembly hardware, refer to the drawings below. Note: The assembly hardware and other
small parts are packaged in separate part bags.
Do not open the part bags until instructed to do so. (The
part bags are not labeled according to the order in which they are to be opened.) If a part is not found in
the part bags, check to see if the part has been preassembled.
ASSEMBLY
Assembly requires two persons.
Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included hex keys and your own phillips screwdriver wire cut-
ters , rubber mallet , and adjustable spanner .
1.
Open part bag B.
Identify the Right Upright (82) (the
Left Upright [69] has a large round hole in the location
shown). Lay the Right Upright flat, and cut the plastic
ties off the lower end. Next, feed the Wire Harness (83)
into the bottom of the Right Upright and pull it out of the
hole in the top. Note: There may be a tie on the end of
the Wire Harness to help you pull it through the hole.
Attach the Right Upright (82) to the bracket on the right
side of the Base (109) with two 1 1/4” Bolts (104) and
two Internal Star Washers (72). (Note: It may be helpful
to use a rubber mallet to fully insert the Right Upright
into the bracket.)
Do not tighten the Bolts yet. Be
careful not to damage the Wire Harness.
Attach the Left Upright (69) to the left side of the
Base (109) in the same way.
Note: There is not a wire
harness on the left side.
82
83
1
69
Hole
109
104
72
Bracket
27
