background image

Inspect and properly tighten all parts of the elliptical
trainer regularly. Replace any worn parts immediately.

The elliptical trainer can be cleaned with a soft cloth
and a small amount of mild detergent. Do not use
abrasives or solvents. 
To prevent damage to the
console, keep liquids away from the console and keep
the console out of direct sunlight.

When storing the elliptical trainer, remove the batter-
ies from the console. Keep the elliptical trainer in a
clean, dry location, away from moisture and dust.

CONSOLE TROUBLE-SHOOTING

If the console does not function properly, replace the
batteries (refer to assembly step 9 on page 8).  

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, first refer to assembly step 8 on page 8 and
remove the Pedals (13, 14). Next, refer to step 7 on
page 7 and remove the Pedal Arms (11, 12). 

Next, remove the four Screws (51) from the right
Pedal Disc (15), and slide the Pedal Disc off. Remove
all Screws (52, 64) from the Right Side Shield (4), and
remove the Right Side Shield. Remove all Screws
(52) from the Left Side Shield (3) and remove the Left
Side Shield.

Next, refer to the drawing below and locate the Reed
Switch (53). Loosen, but do not remove, the indicated
Screw (52). Slide the Reed Switch slightly toward or
away from the Magnet (58) on the flywheel. Retighten
the Screw. Turn the left Pedal Disc (15) for a moment.
Repeat until the console displays correct feedback. 

When the Reed Switch (53) is correctly adjusted, reat-
tach the Side Shields (3, 4), the right Pedal Disc (15),
the Pedal Arms (11, 12), and the Pedals (13, 14).

HOW TO ADJUST THE DRIVE BELT

If you can feel
the pedals slip
while you are
pedaling,
even when
the resistance
knob is turned
to the maxi-
mum setting,
the Drive Belt
(19) may
need to be
adjusted. To
adjust the
Drive Belt, you must remove both side shields. Refer
to the instructions at the left and remove the side
shields.

Next, loosen the M8 x 22mm Flat Head Screw (68)
and turn the Idler Adjustment Bolt (62) until the Drive
Belt (19) is tight. Once the Drive Belt is tight, tighten
the Flat Head Screw. Reattach the side shields.

11

MAINTENANCE AND TROUBLE-SHOOTING 

64

52

51

52

52

52

64

64

14

12

4

58

53

52

15

15

3

68

62

19

64

Содержание 465S

















Отзывы: