background image

8

IF THE POWER CABLE IS DAMAGED, IT MUST BE REPLACED BY YOUR NEAREST MASTERCUT TECHNICAL SERVICE 
OR QUALIFIED PERSONNEL TO AVOID RISK OF ELECTRIC SHOCK.

PARTS TO CARE FOR WEARING OUT:

DELI MEAT SLICER

KMS-12

WARNING!:

THE TIME SPENT IN GRINDING AND TRUING THE KNIFE EDGE WILL ADD 
TO LONGEVITY OF THE KNIFE AND PROVIDE OPTIMUM EFFICIENCY OF 
YOUR SLICER. REPEAT STEPS “D” AND “E” IF THEY ARE NECESSARY.

PARTS CHEKING

FREQUENCY

VERIFICATION

COMMENTS

BAND

ONCE A MONTH

IF YOU SEE ANY PRODUCT TO YOUR SLICING BLADE 

STOPS. TENSION TO GIVE THE BAND FOR A BETTER 

GRIP ROTATION BETWEEN PULLEYS.

BEARING

DAILY

DO DAILY CLEAN BEARING AREA TO PREVENT BUILDUP 

OF FLUIDS AND WASTES.ALSO OIL (FOOD GRADE 

GREASE) THIS AREA FOR THE PURPOSE OF EXTENDING 

THE LIFE OF BEARING.

MEMBRANE          (ON-OFF)

DAILY

REQUIRED IMMEDIATELY CHANGE SWITCH MEMBRANE 

BREAK IF FAILURE TO PREVENT POST ON OR OFF THE 

INTRODUCTION OF MOISTURE OR OTHER WASTE.

PARTS TO CARE FOR WEARING OUT:

REVIEW OF PARTIES

(SUPPLIES)

FREQUENCY

VERIFICATION

COMMENTS

MOVING TRUCK (BARS 

MEDIA)

ONCE A WEEK

KEEP FREE OF WASTE (POWDER, FOOD, ETC.) BARS 

ALSO KEEP MOVING THIN OIL LUBRICATED, DO NOT USE 

OIL OR FAT THICK AS IT AFFECTS THE MOVEMENT.

KNIFE

ONCE A WEEK

SHARPENING BLADE HEAVY CUT IF YOU NOTICE, OR IF 

YOU NOTICE WHEN EXCESS SCRAP SLICING. (CUT TO BE 

GENTLE, EASY CLEAN).

SHARPENING STONES AND

SEATED

DAILY

IT IS RECOMMENDED THAT THE STONES ARE KEPT 

COVERED OR PROTECTED FROM WASTE TO EXTEND 

THE LIFE OF THESE. MAKE SURE BEFORE THE BLADE 

SHARPENING IS FREE TO PREVENT WASTE

CLOGGED PORES OF STONES.

Содержание KMS-12













Отзывы: