background image

                                                                                                                                               KG-12-FS 

 

 
4.-TO  CLEAN  CASE  (5)  ENCLOSURE  USE  DAMP  CLOTH  WITH  DETERGENT  (NEVER  HOSE 

DOWN OR SUBMERGE CASE ENCLOSURE IN WATER OR OTHER LIQUID). RINSE WITH A 
DAMP CLOTH AND DRY. 

 
5.- REASSEMBLE  THE  MAIN  COMPONENTS  TAKING  CARE  OF  THE  PIN(9)  ALIGNMENT  IN 

THE HEAD WITH THE NOTCH ON THE BOTTOM OF THE PL

ATE . (SEE DETAIL “B”) 

 

VII.- MAINTENANCE:

 

 

ALWAYS UNPLUG OR DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE 

CLEANING OR SERVICE. 

 

1.- TO  ASSURE  QUALITY  PRODUCT,  YOUR  KNIFE(18)  AND  PLATE(19)  MUST  HAVE  SHARP 

EDGES, REGULARLY REPLACE OR SEND FOR SHARPENING THESE COMPONENTS. 

 
2.- RELUBRICATE THE NYLON WASHER (15) REGULARLY WITH THE GREASE INCLUDED IN 

THE BOTTLE(25) INSPECT AND REPLACE WHEN NO LONGER SERVICEABLE. 

 

NOTE: A SYMPTOM TO RECOGNIZE  A WORN NYLON WASHER(15) IS BY TIGHTEN THE 
RING  TOTALLY  WITHOUT  OBTAINING  PROPER  TENSION  BETWEEN  PLATE(19)    AND 
KNIFE(18) . 

 
3.- THE  GEAR  BOX  OF  THIS  GRINDER  IS  SEALED  AND  SHOULD  BE  SERVICED  ONLY  BY                                                    

APPROVED  TECHNICIAN,  THE  TRANSMISSION  OIL  SHOULD  BE  CHANGED  AT  LEAST 
EVERY TWO (2) YEARS OF NORMAL OPERATION. 

 
4.-  TO  INSURE  QUALITY  PRODUCT,  REGULARLY  REPLACE  OR  SEND  FOR  SHARPENING 
THESE COMPONENTS: 
 

 

REVIEW BY CONSUMER 

 

FREQUENCY OF 

VERIFICATION 

 

COMMENTS

 

 

BLADE (18) 

PLATE (19) 

 
 

 

ONCE A MONTH 

CHECK  THE  APPEARANCE  OF  THE  PLATE  AND 
THE  EDGE  OF  THE  KNIFE.  THESE  MUST  BE 
SUBMITTED NO  SCRATCHES.  IF  THE MEAT HAS A 
BAD PRESENTATION PLATE AND BLADE. 

 

MEMBRANES (ON-OFF) 

 

DAILY 

CHANGE  IS  REQUIRED  IMMEDIATELY  MEMBRANE 
SWITCH  BREAK  IN  CASE  OF  FAILURE  TO 
PREVENT  POST  ON  OR  OFF  THE  INTRODUCTION 
OF MOISTURE OR OTHER DEBRIS. 

 
 

TRANSMISSION OIL 

 

 

EVERY YEAR AND A 

HALF 

ASSESS  OIL  LEVEL  IN  ORDER  TO  VERIFY  THE 
VOLUME (SEE INSTRUCTIONS FOR EVALUATION). 
IN  THE  ABSENCE  FILL  AND  /  OR  BENEFIT  FOR 
NEW OIL CHANGE (CHECK WITH YOUR DEALER). 

 
 

WORM (16) 

 
 

ONCE A MONTH 

 
VALIDATE  THAT  THERE  IS  NO  EXCESS  OF  GAME 
THAT  ALLOWS  THE  BLADE  CAN  ROTATE  ABOUT 
THE  PIN  (DOWEL  THEN  REPLACE).  SPIKE  REAR. 
REVISION  APPLY  BETWEEN  ITSELF  AND  REAR 
SPINDLE GEAR FRAME. 

 
 

HEADSTOCK (13) 

 

 
 

ONCE A MONTH 

 
CHECK  FRONT  HEAD  SCREW  TO  PREVENT 
ACCIDENTS BAD NUT ASSEMBLY. 
SURE GRIP LEVER NOT BE A STICKING WITH THE 
CABINET  WHEN  "HOLD  THE  HEAD",  IF  THE  HEAD 
IS SAFARCE COULD LOOSE, IT INDICATES THAT IT 
IS TIME TO CHANGE THE HEAD. 

Содержание KG-12-FS









Отзывы: