i
www.printek.com
|
P:
888.211.3400
|
F:
269.222.1229
|
E:
FCC Part 15 Class B
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Normal use distance please maintain 5cm
This equipment complies with Canadian and FCC radiation exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Part 15.21 Caution: Changes or modifications not expressly approved by Printek, LLC could void the user’s authority to
operate the equipment.
Canadian Department of Communications Radio Interference Statement
This
device
complies
with
Industry
Canada
license
‐
exempt
RSS
standard(s).
Operation
is
subject
to
the
following
two
conditions:
1)
this
device
may
not
cause
interference;
2)
this
device
must
accept
any
interference,
including
interference
that
may
cause
undesired
operation
of
the
device.
Under
Industry
Canada
regulations,
this
radio
transmitter
may
only
operate
using
an
antenna
of
a
type
and
maximum
(or
lesser)
gain
approved
for
the
transmitter
by
Industry
Canada.
To
reduce
potential
radio
interference
to
other
users,
the
antenna
type
and
its
gain
should
be
so
chosen
that
the
equivalent
isotropically
radiated
power
(e.i.r.p.)
is
not
more
than
that
necessary
for
successful
communication.
Maximum
power
output
plus
maximum
antenna
gain
of
the
EUT
is:
4.5W/m
2
,
Limit
is
10Wm
2
.
Le
présent
appareil
est
conforme
aux
CNR
d'Industrie
Canada
applicables
aux
appareils
radio
exempts
de
licence.
L'exploitation
est
autorisée
aux
deux
conditions
suivantes
:
(1)
l'appareil
ne
doit
pas
produire
de
brouillage,
et
(2)
l'utilisateur
de
l'appareil
doit
accepter
tout
brouillage
radioélectrique
subi,
même
si
le
brouillage
est
susceptible
d'en
compromettre
le
fonctionnement.
Conformément
à
la
réglementation
d'Industrie
Canada,
le
présent
émetteur
radio
peut
fonctionner
avec
une
antenne
d'un
type
et
d'un
gain
maximal
(ou
inférieur)
approuvé
pour
l'émetteur
par
Industrie
Canada.
Dans
le
but
de
réduire
les
risques
de
brouillage
radioélectrique
à
l'intention
des
autres
utilisateurs,
il
faut
choisir
le
type
d'antenne
et
son
gain
de
sorte
que
la
puissance
isotrope
rayonnée
équivalente
(p.i.r.e.)
ne
dépasse
pas
l'intensité
nécessaire
à
l'établissement
d'une
communication
satisfaisante.
La
puissance
de
sortie
maximale
plus
gain
d'antenne
maximal
du
EUT
est
:
4.5W/m
2
Limite
est
10W/m
2
