Primus PSS500 Скачать руководство пользователя страница 6

Страница: 6 / 6

DID

DID Y

YOU KNO

OU KNO

OU KNOW?

PRIMUS

STERILIZER Company, LLC • 6565 South 118th Street • Omaha, NE 68137• Phone (402) 344-4200 • Fax (402) 344-4242

Page 6 of 6

NO: 258

APRIL 30, 2014

PSS500 CONTROL BOARD JUMPERS - FIELD CONFIGURATION
(CONTINUED)

Step 10

Firmly press down on the SBC196 board unit it is correctly seated.

Step 11

Attach the four nylon washers and small nuts to the stand-offs.

Step 12

Attach the ribbon cable to the SBC196 board with the red stripe at
the top of the outer socket (where the yellow capacitor is located).
Be careful not to bend any pins when re-attaching the cable end.

Step 13

Verify all connections are secure.

Step 14

Return power to the control board.

Additional Information

For further information and photographs, refer to PRIMUS

DYK #202 - PSS5

Control Board Jumper Configuration and DYK #238 - PSS500 Controller
Components #5 – Interface Board Jumpers.

Содержание PSS500







Результаты поиска

Содержание PSS500

Отзывы:

Бренды по названию

Популярные бренды

Primus PSS500, Конфигурация

Результаты поиска

Содержание PSS500

Отзывы:

Бренды по названию

Популярные бренды