Prima LPR808 страница 31 Скачать руководство пользователя

Страница: 31 / 40

installation instructions

step 3: connect to the electricity supply

This appliance must be connected by a
competent person, using fixed wiring via
a double pole switched fused spur outlet,
with a contact separation of 3mm at all
poles.

use a 13 amp fuse.

We recommend that the appliance is
connected by a qualified electrician,
who will comply with the I.E.E. and local
regulations.

Warning:

This appliance must be earthed.

The wires in the mains lead are coloured
in accordance with the following code:
Green & Yellow = earth, Blue = neutral,
Brown = live.

typical example of a double pole fuse spur

outlet

As the colours of the wires in the mains
lead for the appliance may not correspond
with the coloured markings identifying the
terminals in your spur box, proceed as
follows:

1. The wire which is coloured green and

yellow must be connected to the

terminal marked

(Earth)

or coloured green.

2. The wire which is coloured blue must

be connected to the terminal marked

(Neutral) LOAD or coloured Black.

3. The wire which is coloured brown must

be connected to the terminal marked

(Live) LOAD or coloured Red.

If the supply cord is damaged, obtain a
special cord from the Customer Support
Helpline, which must be fitted by a
qualified person.

Step 3: Connect to the electricity

supply

This appliance must be connected by

a competent person, using fixed

wiring via a double pole switched

fused spur outlet, with a contact

separation of 3mm at all poles.

Use a 13 amp fuse.

We recommend that the appliance is

connected by a qualified electrician,

who will comply with the I.E.E. and

local regulations.

Warning:

This appliance must be

earthed.

The wires in the mains lead are

coloured in accordance with the

following code: Green & Yellow =

earth, Blue = neutral, Brown = live.

As the colours of the wires in the mains

lead for the appliance may not

correspond with the coloured markings

identifying the terminals in your spur

box, proceed as follows:
1. The wire which is coloured green

and yellow must be connected to

the terminal marked

(Earth)

coloured green.

2. The wire which is coloured blue

must be connected to the terminal

marked

(Neutral)

LOAD

coloured Black.

3. The wire which is coloured brown

must be connected to the terminal

marked

(Live)

LOAD

or coloured

Red.

If the supply cord is damaged, obtain

a special cord from the Customer

Support Helpline, which must be fitted

by a qualified person.

Installation Instructions

USE A 13 AMP FUSE

FUSE

Typical example of a double

pole fuse spur outlet

Live

Earth

Neutral

Cable

N L

OAD

SUPPLY

250

Step 3: Connect to the electricity

supply

This appliance must be connected by

a competent person, using fixed

wiring via a double pole switched

fused spur outlet, with a contact

separation of 3mm at all poles.

Use a 13 amp fuse.

We recommend that the appliance is

connected by a qualified electrician,

who will comply with the I.E.E. and

local regulations.

Warning:

This appliance must be

earthed.

The wires in the mains lead are

coloured in accordance with the

following code: Green & Yellow =

earth, Blue = neutral, Brown = live.

As the colours of the wires in the mains

lead for the appliance may not

correspond with the coloured markings

identifying the terminals in your spur

box, proceed as follows:
1. The wire which is coloured green

and yellow must be connected to

the terminal marked

(Earth)

coloured green.

2. The wire which is coloured blue

must be connected to the terminal

marked

(Neutral)

LOAD

coloured Black.

3. The wire which is coloured brown

must be connected to the terminal

marked

(Live)

LOAD

or coloured

Red.

If the supply cord is damaged, obtain

a special cord from the Customer

Support Helpline, which must be fitted

by a qualified person.

Installation Instructions

USE A 13 AMP FUSE

FUSE

Typical example of a double

pole fuse spur outlet

Live

Earth

Neutral

Cable

N L

OAD

SUPPLY

250

Содержание LPR808









































Результаты поиска

Содержание LPR808

Отзывы:

Похожие инструкции для LPR808

Бренды по названию

Популярные бренды

Prima LPR808, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание LPR808

Отзывы:

Похожие инструкции для LPR808

Бренды по названию

Популярные бренды