Prima LPR808 страница 18 Скачать руководство пользователя

Страница: 18 / 40

installation instructions - 60cm

step 1: Prepare installation

Do not lift the appliance by the door handle.

Whilst every care is taken to eliminate
burrs and raw edges from this product,
please take care when handling - we
recommend the use of protective gloves
during installation.

Please note that the weight of this
appliance is approximately 31kg
(unpacked). Take care when lifting it
into the housing unit - always use an
appropriate method of lifting.

Remove the fixing screws from the
polythene bag on the top of the appliance,
but leave the appliance in the base tray
packaging until you are ready to install it.

If this appliance is to be installed near to
a corner where the adjacent cabinets run
at right angles forward of the appliance,
there must be a gap of at least 90 mm
between the appliance and the cabinets,
to prevent overheating of the cabinets.

Housing dimensions

The appliance is designed to fit into a
standard 600mm wide housing unit with
minimum internal dimensions as shown.

591mm is to the underside of the worktop
when the appliance is built under, or to the
underside of the panel above, when the
appliance is installed into a tall housing
unit.

Step 1: Prepare installation
Do not lift the appliance by the

door handle.

Whilst every care is taken to eliminate

burrs and raw edges from this product,

please take care when handling - we

recommend the use of protective

gloves during installation.
Please note that the weight of this

appliance is approximately 31kg

(unpacked). Take care when lifting it

into the housing unit - always use an

appropriate method of lifting.
Remove the fixing screws from the

polythene bag on the top of the

appliance, but leave the appliance in

the base tray packaging until you are

ready to install it.

If this appliance is to be installed near

to a corner where the adjacent

cabinets run at right angles forward of

the appliance, there must be a gap of

at least 90 mm between the appliance

and the cabinets, to prevent overheating

of the cabinets.

Housing dimensions

The appliance is designed to fit into a

standard 600mm wide housing unit

with minimum internal dimensions as

shown.
591mm is to the underside of the

worktop when the appliance is built

under, or to the underside of the panel

above, when the appliance is installed

into a tall housing unit.

585

min

560mm

595mm

550mm

568

547mm

20mm

min 550mm

30 - 80mm

min

580

min

590

12mm

gap in plinth

6mm

588

90mm (minimum)

Installation Instructions

Step 1: Prepare installation
Do not lift the appliance by the

door handle.

Whilst every care is taken to eliminate

burrs and raw edges from this product,

please take care when handling - we

recommend the use of protective

gloves during installation.
Please note that the weight of this

appliance is approximately 31kg

(unpacked). Take care when lifting it

into the housing unit - always use an

appropriate method of lifting.
Remove the fixing screws from the

polythene bag on the top of the

appliance, but leave the appliance in

the base tray packaging until you are

ready to install it.

If this appliance is to be installed near

to a corner where the adjacent

cabinets run at right angles forward of

the appliance, there must be a gap of

at least 90 mm between the appliance

and the cabinets, to prevent overheating

of the cabinets.

Housing dimensions

The appliance is designed to fit into a

standard 600mm wide housing unit

with minimum internal dimensions as

shown.
591mm is to the underside of the

worktop when the appliance is built

under, or to the underside of the panel

above, when the appliance is installed

into a tall housing unit.

585

min

560mm

595mm

550mm

568

547mm

20mm

min 550mm

30 - 80mm

min

580

min

590

12mm

gap in plinth

6mm

588

90mm (minimum)

Installation Instructions

Содержание LPR808









































Результаты поиска

Содержание LPR808

Отзывы:

Похожие инструкции для LPR808

Бренды по названию

Популярные бренды

Prima LPR808, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание LPR808

Отзывы:

Похожие инструкции для LPR808

Бренды по названию

Популярные бренды