Prima LPR808 страница 30 Скачать руководство пользователя

Страница: 30 / 40

installation instructions

step 2: connect to gas supply

1. The inlet to the appliance is ISO 7

- Rp ½” internal thread situated

towards the top right hand rear corner.

2. Fit the bayonet connection to the wall

in the shaded area as shown.

The shaded area shown is applicable to
installations in minimum depth cabinets.

If more room is available, the bayonet
fixing area can be extended, provided that
the flexible tube does not obscure the fan
intake.

3. Use a 900mm - 1125mm length of

flexible connector. The flexible

connector shall be fitted such that it

cannot come into contact with a

moveable part of the housing unit (eg;

drawer) and does not pass through

any space susceptible of becoming

congested. Make sure that the flexible

connector does not block the cooling

fan inlet.

4. Flexible connections should comply

with BS 669. Parts of the appliance

likely to come into contact with a

flexible connector have a temperature

rise of less than 70°C.

5. Rigid connections must be accessible

to disconnect for servicing. Cut a

150mm square hole in the right hand

rear corner of the support shelf for the

supply pipe.

6. Make sure all connections are gas

sound.

Step 2: Connect to gas supply

1. The inlet to the appliance is ISO 7

- Rp

⁄

” internal thread situated

towards the top right hand rear

corner.

2. Fit the bayonet connection to the

wall in the shaded area as shown.
The shaded area shown is

applicable to installations in

minimum depth cabinets.
If more room is available, the

bayonet fixing area can be

extended, provided that the

flexible tube does not obscure the

fan intake.

3. Use a 900mm - 1125mm length of

flexible connector. The flexible

connector shall be fitted such that

it cannot come into contact with a

moveable part of the housing unit

(eg; drawer) and does not pass

through any space susceptible of

becoming congested. Make sure

that the flexible connector does not

block the cooling fan inlet.

4. Flexible

connections

should

comply with BS 669. Parts of the

appliance likely to come into

contact with a flexible connector

have a temperature rise of less

than 70˚C.

5. Rigid connections must be accessible

to disconnect for servicing. Cut a

150mm square hole in the right

hand rear corner of the support

shelf for the supply pipe.

Make sure all connections

are gas sound.

Installation Instructions

60mm

square

rear

wall

Содержание LPR808









































Результаты поиска

Содержание LPR808

Отзывы:

Похожие инструкции для LPR808

Бренды по названию

Популярные бренды

Prima LPR808, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание LPR808

Отзывы:

Похожие инструкции для LPR808

Бренды по названию

Популярные бренды